How much does it cost to replace U joints on a Jeep Wrangler?
Jeep Wrangler U-Joint Replacement Cost Estimate. The average cost for a Jeep Wrangler u-joint replacement is between $244 and $274. Labor costs are estimated between $115 and $145 while parts are priced at $129. This range is based on the number and age of Jeep Wrangler’s on the road.
What is AU joint on a Jeep?
A u-joint, or universal joint, is a component that connects the driveshaft to the differential, and sometimes connects the driveshaft to the transmission or two driveshafts to each other. It’s a cross shaped piece with a bearing at each end, that allows for lateral and side to side movement of the driveshaft.
How many universal joints does a jeep have?
There are three u-joints up front and two in the rear. A highly recommended upgrade is the Spicer 5-1310x which is sealed, as well as a stronger, more durable upgrade for the standard 1310 u-joint.
What are 1310 U joints?
For most cars, 1310-series U-joints are typical choice, but for performance applications, the rugged 1350-series joints are the better choice. The larger the series number, the larger the trunnion. Trunnions are the protruding shafts that the caps ride over….U-Joint Sizes.
| Series | Width | Cap Diameter |
|---|---|---|
| 7290 | 2.622 | 1.126″ |
What is the difference between a 1310 and 1330 U joint?
While the front and rear u-joint can be of two different sizes the shaft is only as strong as the smaller one. The 1310 series u-joint measures approximately 3 1/4 inches wide. The 1330 and 1350 both measure approximately 3 5/8 wide.
What is the difference between 1310 and 1350 U joints?
Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.
How much power can a 1310 U Joint handle?
The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque. While the 1310 series, the stock size for most Jeeps, is rated for 1,600 lb-ft of torque.”
How much HP can a 1350 U Joint handle?
1350 is typically for the 650+ horsepower. 1310s are for under 500hp. Keep in mind, you will only be as strong as your weakest link.
Are U joints strong?
Standard u-joints sizes are classified by series, with each series having specific cap diameter and overall joint width. Typically speaking, a higher series number translates to a stronger joint….Understanding U-Joints.
| U-Joint Series | Continuous Lifetime Operating Torque | Yield Torque |
|---|---|---|
| 1350 | 210 lb-ft | 2,260 lb-ft |
What are the best U joints?
10 Best U Joints in 2020 – Reviews and Buying Guide
- Spicer 5-153X U-Joint Kit.
- ACDelco 45U0106 Professional U-Joint.
- All Balls 19-1005 U-Joint.
- Moog 534G Universal Joint.
- Chrome Polished Steering Shaft U Joint.
- Spicer 5-1310X Life Series.
- GMB 210-0213 Universal Joint.
- Ensun ¾-inch Steering Shaft Universal Joint.
Are Spicer U joints better than Moog?
Frankly, there’s a very simple answer: If you drive a Jeep, I recommend you to go for Spicer joints. This specific U joint is the absolute best replacement part you can get for virtually all Jeep models. For most other vehicles – and especially light trucks or commuter cars, MOOG are an affordable and optimal solution.