What is meant by religious tolerance?
Religious Tolerance refers to the ability to appreciate spiritual values, beliefs and practices which are different from your own.
What is an example of religious tolerance?
Turkey is 90 percent Muslim. The priest of the Armenian Orthodox Church, using a key made in 1835, opens the doors to a Christian world within a Muslim one. The priest is one of a few who come from another part of Istanbul to serve the faithful.
What are the effects of tolerance?
With certain classes of drugs, like opioids, tolerance can increase the risk of dependence, addiction, and overdose. When your body develops tolerance, using higher doses increases the risk of overdose. A benefit of tolerance might be fewer side effects as your body gets used to the medication.
What does tolerance mean?
capacity to endure pain
How many types of tolerance are there?
Today, there are 14 types of geometric tolerances by the number of symbols, and 15 types based on classification. These are grouped into form tolerance, orientation tolerance, location tolerance, and run-out tolerance, which can be used to indicate all shapes.
What is the purpose of GD?
Geometric Dimensioning & Tolerancing ( GD ) is a language representative of engineering drawings to classify deviations and tolerance of part measurements and geometric analysis. It is an efficient way of communicating measurement conditions and specification of a part.
What is tolerance in pharmacy?
Tolerance is a person’s diminished response to a drug, which occurs when the drug is used repeatedly and the body adapts to the continued presence of the drug. Resistance refers to the ability of microorganisms or cancer cells to withstand the effects of a drug usually effective against them.
What is a H7 hole tolerance?
For example, in H7/h6 (a commonly-used fit) H7 represents the tolerance range of the hole and h6 represents the tolerance range of the shaft. The potential range of clearance or interference can be found by subtracting the smallest shaft diameter from the largest hole, and largest shaft from the smallest hole.
Is H7 a press fit?
H8/r7, H7/p6, H7/r 6, P7/h6, R7/h6 Pressed fits with guaranteed interference. Assembly of the parts can be carried out using cold pressing. Hubs of clutch disks, bearing bushings. H8/s7, H8/t7, H7/s6, H7/t6, S7/h6, T7/h6 Pressed fits with medium interference.
What is shaft tolerance?
For hydrostatic and aerostatic bearing design, shaft tolerance and hole tolerance are added and given as one clearance tolerance. The upper clearance limit is 50% higher than the lower clearance limit, and the difference between the two limits is equal to the combined tolerance on the hole and the shaft diameters.
What is k6 tolerance?
k6. Fitting which requires an iron hammer or hand press for assembling, disassembling. (a key or the like is necessary to prevent inter-part shaft rotation).
Is 2102 a standard tolerance?
This part of IS0 2758 is intended to simplify drawing indica- tions and it specifies general tolerances for linear and angular dimensions without individual tolerance indications in four tol- erance classes. NOTE 1 – The concepts behind the general tolerancing of linear and angular dimensions are described in annex A.
What does interference fit mean?
An interference fit, also known as a press fit or friction fit is a form of fastening between two tight fitting mating parts that produces a joint which is held together by friction after the parts are pushed together.
Is standard for fits and tolerances?
The standard was originally published in 1959. It was subsequently revised in 1963 taking assistance from ISO/R 286-1962 ‘IS0 system of limits and fits, general tolerances and deviations’. horology’. IS 2709 : 1982 ‘Guide for the selection of fits ( first revision )’ and !
What are the three types of fits?
The three main categories are: Clearance fit. Transition fit. Interference fit.
Which is grade of tolerance?
For SI measurements, a system of tolerance grades defined in ISO 286 is frequently used and identified by the letters IT followed by a number specifying how precise the requirements are, relative to the nominal size of a part. For example, IT14 refers to a group of tolerances used in manufacturing.
Why is it important in manufacturing to determine allowances?
Allowance between parts that are assembled is very important. For example, the axle of a car has to be supported in a bearing otherwise it will fall to the ground. If there was no gap between the axle and the bearing then there would be a lot of friction and it would be difficult to get the car to move.