What hinges to use for cabinet doors?
Two types of hinge installations are available: Concealed (Mortise) Hinges: Permanent installation hinges that are attached inside the cabinet door and frame, best used for inset doors. Decorative (Nonmortise) Hinge: Don’t require placement into the cabinetry and simply fasten with screws.
Can you put hidden hinges on old cabinets?
It really is amazing what hidden hinges can do to update the look of any cabinetry. And if you ever get the chance to fully replace your cabinets or cabinet doors, you can reuse these hinges. This type of hinge is not cheap, so the more mileage you can get out of them, the better.
What type of door hinge do I need?
Hinge Size Doors up to 60 inches need two hinges. Doors over 60 inches, but not over 90 inches, need three hinges. Doors over 90 inches, but not over 120 inches, need four hinges.
What are the different types of cabinet hinges?
- WRAP AROUND HINGES. Full Wrap-Around: Frame wing wraps three sides of the frame and screws to the inside edge.
- FACE FRAME (SEMI-CONCEALED) HINGES. The frame wing is visible when the cabinet door is closed.
- SURFACE MOUNT HINGES.
- INSET HINGES.
- OVERLAY HINGES.
- REVERSE BEVEL HINGES.
How do I know what type of cabinet hinges I have?
You should check the diameter of the hole in the door that your current hinge sits in – these are usually 26mm, 35mm or 40mm for larger hinges. It’s important to measure the hole in the door and not the hinge itself as the hinge may be slightly smaller.
What is a full overlay cabinet hinge?
Full Overlay: A full-overlay door covers all or nearly all of the front edge of the cabinet. This overlay type typically is used for doors at the ends of a cabinet. This hinge will allow the door to cover half of the partition wall (or approximately 3/8″).
What is the difference between a full overlay and half overlay hinge?
Full overlay hinges are for individual cabinets or the cabinets on either end of a run of cabinets. Half overlay hinges are intended for pairs of doors in the middle of a run of cabinets, where two doors have their hinges mounted on opposite sides of a shared middle partition.
How much does a full overlay hinge cover?
1 Answer. A “Full” Overlay normally means it overlays 3/4″ inch. This is because it is made to fully overlap a 3/4″ faceless plywood end. These will often be intended for side mounted hinges.
How do I know my overlay hinge?
Apply a piece of tape to the frame of the cabinet on the hinged side of the door so that it even with the edge of the door. Open the cabinet door and measure from the edge of the tape (inside edge) to the edge of the opening of the cabinet. This is the overlay.
What is a 1/2 inch overlay hinge?
A 1/2″ overlay literally means that all the drawers and doors of a cabinet run will extend half an inch over the frame. This is a classic styling for cabinetry and leaves about two inches of exposed frame in between cabinet doors.
What is a 3/4 overlay hinge?
Overlay Cabinet Hinges – Items tagged as “3/4″ overlay” The overlay is considered the correlation of the cabinet doors to the cabinet face frames. The overlay refers to the size or type of the door, the hinge, or how the cabinet is built.
What is a Blum hinge?
Blum “European-style” hinges are easily adjustable for foolproof installation! Simply turn a screw or cam to make sideway and height adjustments for perfect cabinet door alignment. Side Adjustment Regulates the gaps between doors, cabinets and walls for perfect parallel alignment.
Do hinges need to be recessed?
When you install a door hinge, you need to make notches for it on the edge of the door and on the jamb, or the door won’t close properly. These notches, or mortises, should be just deep enough to allow the surface of the hinge to sit flush with the wood.
How do you measure cabinet hinge overlay?
Line up the edge of your door with the edge of a piece of tape and apply the tape to the face frame of the cabinet (must be on the hinged side of the door). Now, open the cabinet door and measure from the edge of the tape (inside edge) to the edge of the opening of the cabinet. In this case the overlay is 1-1/4″.
What is standard cabinet overlay?
Standard overlay cabinets (also called traditional overlay) tend to be less expensive and do not require hardware because there is enough finger space on the side of the cabinet door or drawer face. They also have more exposed face frame, with at least 1 ¼ inches on all sides of the doors and drawers.
Can you change cabinet hinges to hidden?
Many older kitchens out there have exposed hinges, where you can see the hinge mounted to the cabinet frame. By swapping out that hinge for an updated, hidden hinge, the transformation can really take a space from dated to modern, just like that. Having hidden hinges gives you the freedom to change hardware on a whim.
What is a partial overlay hinge?
Half or Partial overlay hinges are used for a pair of cabinet doors in the middle of a row of cabinets where two doors have their hinges mounted on opposite sides of a shared middle partition. …
Are partial overlay cabinets outdated?
Avoid: Raised panel doors and partial-overlay In fact, they are the style most homeowners who are upgrading are replacing right now. Partial overlay, which do not completely cover the frame visible in a cabinetry run, is also on its way out.
What is partial overlay for Cabinet?
Partial Overlay Cabinets are the most common and least expensive option for your kitchen. The door sits on the cabinet face, leaving a “gap” of usually 1-1 ¼ inch between the doors, allowing the face frame of the cabinet to be seen. Below is a church kitchen that utilized Partial Overlay doors.
What is a Euro style hinge?
European style hinges are a modern high-tech hinge for cabinets. European hinges may also be commonly referred to Blum or Grass hinges, as these are two of the main manufacturers of this type of hinge. They are typically comprised of two parts: the hinge and the mounting plate.
What is the use of European hinges?
The European hinge, also known as the Euro Hinge, was ideal because it could be used on a frameless cabinet and allowed for horizontal and vertical door-alignment corrections.
How do you drill a hole in a European hinge?
To drill the flat-bottomed hole for the cup, you’ll need a 35-millimeter Forstner bit. Mark a depth line ½ inch up the side of the bit, position it on the center point, and bore into the door until you hit the line. Blow out the shavings and test-fit the cup to make sure the hinge flanges touch the door surface.
Should there be a gap between cabinet doors?
Typically there is a 1/16″ – 1/8″ gap between all doors. To move a door laterally, use the tilt screws from the previous step in even increments (e.g. Quarter-turn on the bottom hinge set-screw and quarter-turn on the top hinge set-screw).
How much clearance do you need for cabinet doors?
Tim Inman: One-quarter inch OVERALL would leave you with a one-eighth inch gap all around. That’s about right. If you make the gap much bigger, it looks like sloppy work. If you make it any smaller, you’ll end up with binding doors.