Can Dante Virtual Soundcard be a master clock?
Senior Member. Found this from Dante: “Dante Virtual Soundcard cannot clock itself, and thus requires that at least one other Dante-enabled hardware device, or a third computer running Dante Via, is present on the network for clocking.”
Can Dante Virtual Soundcard act as a clock master?
No special hardware is required; the Dante Virtual Soundcard is installed on a conventional PC or laptop. As long as there is another hardware Dante device in a network to act as clock master, the Dante Virtual Soundcard can enable the PC or Mac to be a source or a destination on the network.
What happens when a master clock fails on a Dante network?
If the leader clock fails for any reason, a new leader clock will be chosen from the existing followers within a few seconds. The transition from one leader clock to the other does not result in any loss of audio. The follower devices free run during the period of leader clock transition.
When a Dante preset is saved Where is the information kept?
Save a Dante Preset All Receiving Dante stream information will be stored in the Preset. When you want to just capture the routings to one or several Dante devices, make sure “Rx Channel Subscriptions” is checked.
Can a Dante device route audio back to itself?
All Dante devices except Ultimo-based (low channel count) devices can route audio to themselves.
Does Dante need Gigabit Ethernet?
What type of Ethernet cable is recommended for Dante? As most Dante devices support gigabit Ethernet, Cat5e or Cat6 cable is recommended.
Is Dante a real time network service?
Dante Controller also provides essential device status information and powerful real-time network monitoring, including device-level latency and clock stability stats, multicast bandwidth usage, and customized event logging, enabling you to identify and resolve potential network issues.
How many channels is a basic Dante Ethernet system?
When used with Gigabit Ethernet hardware (that is, hardware that supports a maximum data rate of one gigabit per second), Dante is capable of routing up to 512 channels of inputs and outputs at resolutions from 48 kHz/24-bit up to 192 kHz/32-bit.
Can you send video over Dante?
The Dante AV Module is capable of sending video (up to 4K 3840×2160) over a 1G network (800 Mbps recommended maximum bit rate) and includes control, transport and synchronization.
Do you need a router for Dante?
Can Dante operate over a Wi-Fi network? No. While possible in principle, the practical limitations of current wireless technology (802.11a/b/ g/n) render reliable performance unachievable. For this reason Dante software such as Virtual Soundcard will not recognize wireless connections for audio data.
How many channels are contained in a multicast flow?
In the first example illustrated below, one multicast flow was created, containing four channels. None of the devices actually require all four channels, but both switches are processing four channels of traffic. In the second example, two flows were created with two channels each.
Is Unicast lower latency than multicast?
A unicast Dante flow allows for the use of much lower latency settings than a multicast flow.
What protocol does Dante assign IP addresses to?
DHCP
What is the maximum number of channels that may be contained in a Unicast flow?
four channels
How many DSCP tags are needed for QoS?
QoS Mapping is a feature which converts layer 2 802.1p tags to layer 3 DSCP tags so that they can safely traverse (in mapped form) 802.1p-incapable links; when the packet arrives for delivery to the next 802.1p-capable segment, QoS Mapping converts from DSCP back to 802.1p tags so that layer 2 QoS can be honored.
Do Dante devices have a maximum number of flows?
A Dante device can have an unlimited number of receive flows.
What advantages does Unicast have over multicast communication Dante?
A unicast Dante flow allows for the use of much lower latency settings than a multicast flow. A Dante device can have an unlimited number of receive flows.
Is multicast UDP?
Note: multicast uses UDP and are sent through switches and hubs. To receive a multicast message a host must be configured to receive on that multicast address. All hosts that are configured to receive packets on a particular address are part of a multicast group.
How does Dante Controller discover a device?
Dante devices discover one another on the network automatically. When connected to a managed IT network, Dante devices obtain IP addresses and network configuration from the DHCP server in the same way that office PCs and printers do.
How do I add a device to my Dante Controller?
Dante automatically discovers devices when they are connected to the Dante network, so you just need to plug your new device into your computer, or connect it to the network switch (or in some cases, you can daisy-chain it to another device). It will appear in Dante Via within seconds.
When a Dante enabled device is plugged into a network?
Automatic network configuration A Dante-enabled device connected to a network will automatically setup its own network configuration, including its IP address. If the network has a DHCP server, which may be the case for installed networks, it will receive its IP configuration using the standard DHCP protocol.
What are diagnostic features of Dante Controller?
Dante Controller provides essential device status information and powerful real-time network monitoring, including device-level latency and clock stability stats, multicast bandwidth usage, and customized event logging, enabling you to quickly identify and resolve any potential network issues.
When Should fiber be used for an Ethernet connection Dante?
When should fiber be used for an Ethernet connection? When runs over 100 meters are required.
What can Dante firmware updater part of Dante Controller do for us?
Dante Updater is a new free Dante firmware management application for Windows and macOS desktops. Dante Updater greatly improves the user experience of updating Dante device firmware, allowing Dante users to update entire networks of devices from multiple manufacturers with just a couple of clicks.
Is Dante Controller free?
Dante Controller is a free application that may be downloaded from our website. Once the connections and routes are initially set up, Dante Controller does not need to be running.