Is the Army regulation that provides safety policy standards?
The ASA(I&E) is the Army’s designated safety and occupational health official and will— (1) Approve policies, issue directives, make recommendations, and issue guidance on Army safety and OH plans, programs, and risk management integration within Army Safety and Occupational Health Program areas.
What regulation covers Army safety?
The Army Safety Program is based on Army Regulation (AR) 385-10 and is applicable to all Army personnel and operations. In the program, safety activities are organized to protect the force and enhance warfighting capabilities through a systematic and progressive process of hazard identification and risk management.
What are the principles of the Army Safety Program?
The U.S. Army Safety Program is based on four major principles: conducting on-going training that is common to both leaders and individuals, treating safety as part of everyone’s responsibilities, maintaining universally established safety planning procedures; and utilizing the after-action review process.
Which Department of Defense Instruction governs the Army Safety Program?
o Implements Army Directive 2016–24, Department of Defense Biological Select Agent and Toxins Biosafety Program (paras 1–4a(4), 1–4n(18), 1–4p(5), 20–2d, 20–12d, and 20–13).
Which of the following establishes the legal requirement for a safe and healthful workplace?
The Occupational Safety and Health Act of 1970 is a U.S. law establishing workplace standards to ensure that employees are protected from hazards that compromise their safety and health.
What are three tactical safety areas?
In addition to the required competencies all safety and occupational health professionals must meet, tactical safety professionals are trained in the following fields:
- Composite risk management.
- Tactical safety.
- Deployment/redeployment accident prevention.
- Joint accident investigation and analysis.
- Electrical/fire safety.
What are the 3 basic categories of control?
There are three main types of internal controls: detective, preventative, and corrective. Controls are typically policies and procedures or technical safeguards that are implemented to prevent problems and protect the assets of an organization.
How does using a continuity book make inspections easier?
How does using a Continuity Book make inspections easier? Continuity Books allow program managers to identify program requirements and document actions accomplished easily. One reason for developing a pre-accident plan is: Ensures accident information is only released to appropriate authorities.
Which safety standards have the highest priority?
The U.S. Department of Defense Standard Practice for System Safety (MIL–STD–882) places the highest priority on elimination of hazards through design selection.
What is the purpose of a continuity book?
A continuity book is: “. . . a reference document produced by an individual to share relevant information concerning a duty or position on which he/she has knowledge.
What are the most frequently occurring material handling injuries?
Back injuries are the most common type of injury reported when the manual movement of materials is required.
What is a recordable?
You must consider an injury or illness to meet the general recording criteria, and therefore to be recordable, if it results in any of the following: death, days away from work, restricted work or transfer to another job, medical treatment beyond first aid, or loss of consciousness.
Which of the following are common causes of material handling injuries?
Lifting and Moving Material The weight and bulkiness of objects lifted are major contributing factors to injuries. Workers also frequently cite body movement as contributing to their injuries. Bending, twisting, and turning are the more commonly cited movements that cause back injuries.
Which of the following best describes the responsibility of the senior occupant?
Calculate the Price
| The Heinrich Model: | All of the above. |
|---|---|
| Which of the following best describes the responsibility of the Senior Occupant in an Army Motor Vehicle? Choose the single best answer. | Ensure the driver is not fatigued, or otherwise impaired, from safely operating the vehicle |
What are the two most common material handling accidents?
Material Handling Most Frequent Cause Of Workplace Injuries
- Material handling (32 percent of total claims)
- Slips, trips and falls (16 percent)
- Being struck by or colliding with an object (10 percent)
- Accidents involving tools (7 percent)
What are some common causes of injuries while handling materials quizlet?
Improper body movement, such as twisting, turning and bending, combined with lifting heavy/bulky materials are significant causes of back and spinal injuries when handling or storing materials.
What precautions should you take to prevent injuries when dealing with heavy loads?
When lifting items that are very heavy, you should wear steel-toed safety shoes or boots to protect your feet and toes. Lift Properly – Use proper lifting techniques: bend at your hips and knees to squat down to your load, keep it close to your body, and straighten your legs to lift.
Which item of PPE should be worn when lifting heavy items?
Use personal protective equipment where needed, such as gloves with good grip and steel-toed boots where appropriate. Implement rest breaks and job rotation for frequent and/or heavy lifting.
What are the 6 safety precautions?
General Precautions
- Your safety is your personal responsibility.
- Always follow the correct procedures.
- Never take shortcuts.
- Take responsibility and clean up if you made a mess.
- Clean and organize your workspace.
- Ensure a clear and easy route to emergency exits and equipment.
- Be alert and awake on the job.
What are the most common ways workers get hurt around machines?
Overview of the Most Common Worksite Machinery Accidents
- Getting on and off equipment or machines.
- Loading and unloading equipment or machines.
- Crowded work area.
- Equipment and machine swing radius.
- Operation of equipment or machines on a slope.
- Buried or overhead obstructions.
- Equipment or machine backing.
What is the most common injury caused by working with machines unsafely OSHA?
Answer: The most common injury caused by working with machinery are cuts and burns.
What is the most safety protection are very common in the machine shop?
Choose proper personal protective equipment (PPE) for the machine shop. Wear safety glasses at all times in the shop. At any time, debris may fly out of a machine and into your eye. Consider a face shield when you are working up close with grinding and cutting job tasks.
What are the 2 types of primary safeguarding methods?
Two primary methods are used to safeguard machines: guards and some types of safeguarding devices. Guards provide physical barriers that prevent access to danger areas.
What are the 4 types of machine guards?
There are four general types of guards:
- Fixed.
- Interlocked.
- Adjustable.
- Self-adjusting.
Which parts of a machine must be guarded?
Machine safeguards must meet these minimum general requirements: Prevent contact: The safeguard must prevent hands, arms or any other part of a worker’s body from contacting dangerous moving parts. Be secure: Workers should not be able to easily remove or tamper with the safeguard.
What machine parts always require guards?
The following are some examples of machines requiring point of operation guarding:
- Guillotine cutters.
- Shears.
- Alligator shears.
- Power presses.
- Milling machines.
- Power saws.
- Jointers.
- Portable power tools.
Which machine motion is the most dangerous?
Transverse motion (movement in a straight, continuous line) creates a hazard because a worker may be struck or caught in a pinch or shear point by the moving part. Reciprocating motions. Warning: Exposure to rotating shafts is the most dangerous machine safeguarding hazard.
Do guards prevent accidents on power machines?
Moving machine parts have the potential to cause severe workplace injuries, such as crushed fingers or hands, amputations, burns or blindness. Safeguards are essential for protecting workers from these preventable injuries.
How are machine guards meant to be used?
The purpose of machine guarding is to protect the machine operator and other employees in the work area from hazards created during the machine’s normal operation. This would include hazards of concern such as: ingoing nip points, rotating parts, reciprocating, transversing, and/or flying chips & sparks.