What type of cable is used by floppy drives?

What type of cable is used by floppy drives?

Interface to the floppy disk drive The controller connects to the drive using a flat ribbon cable with 34 connectors split between the host, the 3.5″ drive, and the 5.25″ drive. This type of cable is called a universal connector.

Can floppy disks be converted?

Most computers made in the last decade no longer come with a floppy disk reader leaving you to use an external drive to access them. At EverPresent we offer the ability to read all types of storage formats and we’ll convert your floppy disk to digital or transfer your floppy disk to a DVD.

What do you call the cable that attaches the motherboard to the floppy drive?

A. R. A thin, flat, multiconductor cable that is widely used for internal peripheral connections in electronic systems. In a PC, a 34-wire ribbon connects the floppy drive (if present) to the motherboard.

What will happen if you plug a floppy drive cable in backward?

Plugging a floppy cable in backwards was harmless, but the drives wouldn’t work. Unfortunately, if you offset the cable, sometimes it can damage the drive permanently because it could send signals to pins that couldn’t handle them.

What cables should be connected to motherboard?

Typical systems have at least two such cables: a 34-wire ribbon cable connecting the floppy disk drive to the FDD controller interface on the motherboard, and an IDE cable connecting the hard drive and CD- or DVD-ROM drive to the primary IDE interface connector on the motherboard.

Can cables touch the back of the motherboard?

Bare wires cannot touch the motherboard, but wires inside insulation can touch it and not cause any harm.

Do I need to connect both CPU power cables?

You actually in most cases only need one of the EPS 8pin cables for CPU power, but in many other cases in which the motherboard has 2 8pin or an 8 + 4pin configuration, you really should plug both in.

What all needs to be plugged into the motherboard?

Once the motherboard is physically installed into the computer, the Fpanel (short for front panel connectors) must be connected. This panel controls such things as the power button, reset button, hard drive light, and power light.

What are the basic steps of installing a motherboard?

Before Getting Started

1. Unpack the board. Open your motherboard’s box.
2. Measure blanking plate.
3. Remove unnecessary bits.
4. Install the blanking plate.
5. Measure where the motherboard goes.
6. Fit the risers.
7. Slide the motherboard into place.
8. Screw the motherboard down.

How hard is it to put a PC together?

Building your own computer is actually pretty simple. Don’t be afraid to dive right in — all you’ll need is a screwdriver, patience, and the ability to follow simple instructions. This process is about building desktop PCs, of course. It’s nowhere near as easy to build your own laptop.

What is the largest connector on the motherboard?

The connector that brings power from your power supply to the main motherboard power is probably the largest power connector that you’ll see on the motherboard. This is providing 3.3 volts, 5 volts, and 12 volts of power to the motherboard. And you may see 20 pin connectors, or 24 pin connectors.

Can every CPU fit into any motherboard?

CPUs are typically optimized to work with one type of memory or the other, and you cannot mix them on a motherboard since they require completely different sockets.

What two colors touched between the power connectors?

Green or green with a yellow stripe. This is the ground lead. It should be connected to the PC case and should help ground the power supply to the case.

What is a BTX motherboard?

BTX (for Balanced Technology eXtended) is a form factor for motherboards, originally intended to be the replacement for the aging ATX motherboard form factor in late 2004 and early 2005. The first company to implement BTX was Gateway Inc, followed by Dell and MPC.

Is BTX better than ATX?

BTX is the newer standard, and is the intended successor to ATX. 2. BTX focuses more on airflow than ATX. BTX requires a certain arrangement of motherboard components to maximize cooling, while ATX does not.

Are BTX motherboards still made?

Nope. No consumer btx boards were ever produced afaik. At the time they were strictly an oem affair. So Blaise170 no sorry, its been well over 6 years since a consumer BTX board has been available.

What is BTX?

Balanced Technology EXtended

What is BTX used for?

BTX/HPG is used primarily as feedstock for benzene extraction. The remaining components are further separated into toluene and xylene. Benzene is primarily used for ethylbenzene to styrene and cumene to phenol production. The third largest use of benzene is in the production of cyclohexane, a nylon precursor.