Will a H22 fit in my Accord?

Will a H22 fit in my Accord?

The accord throttle body is smaller than the prelude part, so all the work you just did will be gasping for air right about when VTEC switches. The accord throttle body works fine for regular sedan driving. The h22a will breather deeper and easier, especially at high revs where the Accord engine never ventured.

Which Hondas have H22 engines?

It was developed by Honda to be able to enter into the 2-liter class of international racing. H-Series consisted of two different displacements; H22 2.2 L (2,157 cc) and H23 2.3 L (2,259 cc)….

Honda H engine
Power output	160–220 PS (118–162 kW; 158–217 hp)
Torque output	152–164 lb⋅ft (206–222 N⋅m)

What cars have a H22 engine?

This is the most dynamic out of all H22 engines, it was installed in Honda Prelude Type S and SiR S-Spec, and in Honda Accord Euro R. It boasts 220 HP @ 7,200 rpm and 221 Nm @ 6,500 rpm. The H22A Redtop engine has dome pistons, which increases the compression ratio to 11.

How do I know what Honda ECU I have?

– All Honda ECU’s have an ECU part number which is located on the side of the ECU which allows for easy identification. The middle three characters are the most useful to identify what type of ECU it is. Different generation ECUs may use the same characters.

Is a P06 ECU VTEC?

For the ECUs like the P05 and P06 that did not require VTEC, the components that are used for VTEC functionality were simply not installed. You can convert the following ECUs to VTEC: P05. P06.

Is a p72 ECU VTEC?

The p72 will work for a b16 head AFAIK. You may have a hard time locating a p72 obd1 ECU, and they don’t come cheap. You can’t use a stock LS ecu since it has no way of controlling VTEC.

Is Hondata an ECU?

Hondata modifies standard Honda engine computers (ECUs), adding features and expanding the capabilities of the ECU (e.g. for forced induction). These modifications are available either as a reflash, or a fully tunable system.

How can you tell if you have a P28 ECU?

Model (P28/P72/etc) Take a look at the side of your ECU, you’ll see 37820-PXX-XXX. The numbers following the P, like P28 or P30 are very important. Here are some things to note about the most common variants: P05 – Civic CX – Most basic supported ECU.

What OBD is a P28 ECU?

Uhh, P28 is for 92-95 Si/EX and is an OBD1 ECU. It will NOT plug in to a D16Y7/8 OBD2A car without a harness adapter and 2-wire IACV swap (on D16Y7)!

What does a pr4 ECU come out of?

any one know what a pr4 ecu powered orginally? It is out of a 90 LS. Redline is at 6,800. The 7,200 rev limit was for the 94 plus LS’s.

How do I know if I have obd1 or OBD2?

obd1 dizzy: and yet another way to tell is to take the dizzy off and spin the piece that goes in the head that attaches to the cam. if it clicks every time you spin it a little bit its obd1 but if it clicks after you spin it half way then its obd2. also the obd2 dizzy is lighter then the obd1 dizzy.

What is Honda P06 ECU?

P06=non-vtec.

Is a P75 ECU VTEC?

P28s are already VTEC ECUS. Then you’d have to get it socketted and chipped with a basemap for your setup.

Can you add VTEC to a non VTEC ECU?

yes you can do it.

What car is a P06 ECU from?

Technical Information OBDI Vehicle Reference

Model	Year	Stock ECU
Civic/Del Sol DX/S	92-93	P06
Civic DX	92-95	P08J
Civic Si/EX/	92-95	P28
Civic HX	96-99	P2N

Can a P06 ECU be chipped?

Re: Chipped P06 Ecu question No alterations to anything else, no extra features, nothing. It’s so simple anyone with crome and a burner can reproduce it in about 30 seconds. It’s burned to a 27SF256 chip fresh out of the sleeve.

What is p28 chipped?

DYNO-PRO. Re: what will a chipped p28 ecu do? ( 96 EX) chipping is placing an eprom in the ecu so that you can alter the fuel/ ignition/ vtec ect to gain hp/tq…

What car does a P75 come in?

The P75 is simply a B18B Integra ECU. Those P75 ECUs that came from 1994-1995 Integras are OBDI. And those that came from 1996-2001 Integras are OBDII.

Is B18C a Type R?

This engine can be found in Honda Integra Type R. The B18C Type R engine can be identified by the red valve cover, the 4-1 header, and an intake collector. 8. B18C1 was an engine for USDM Acura Integra GSR.