How do you change a drive belt on a Harley Softail?

How do you change a drive belt on a Harley Softail?

How to Replace Softail Drive Belt

1. Raise the Softail off the ground using the motorcycle stand. Remove the rear axle nut using the pliers.
2. Push the Softail’s rear wheel forward and remove the drive belt from the sprocket.
3. Place the new belt onto the transmission.

How much does it cost to replace a Harley-Davidson drive belt?

Harley drive belts are very strong and durable and only need replacement after thousands of miles of riding. Unless you have a warranty, a replacement will cost a few hundred dollars at your Harley dealer. Do it yourself in about 30 minutes, for less than $50.

How many years will a Harley drive belt last?

“In optimal conditions we have seen belts last 100,000 miles,” says Martin Ginns, Harley-Davidson service business manager.

How tight should a Harley drive belt be?

With a high horsepower engine, it is better to have the belt a little tight rather than loose. A loose belt will break much more readily than a tight one. Most people do not tighten the belt to its proper tension. If you plan on “racing” or hot rodding your bike, invest in a Harley-Davidson BELT TENSION GAUGE (Part No.

When should you change a Harley drive belt?

But even veteran enthusiasts can make the mistake of forgetting to look after their bike’s drive belt, which is strong, stretch-resistant and made from tensile cords. Because a drive belt can last up to 100,000 miles before needing replacement, riders may lose track of this important part of motorcycle maintenance.

How do you tighten a VROD belt?

The belt is adjusted by turning the adjustment cam on the left side. Rotating the cam clockwise will tighten the belt and rotating the axle counterclockwise will loosen the belt. Check the rear belt tension with motorcycle cold, standing upright, transmission in NEUTRAL and no rider on the motorcycle.

Why do Harleys use belt drives?

A belt drive has some even more advantages over other transmission air conditioners (chain and also shaft drives), such as low un-sprung weight, they are quieter, do not corrosion, resist environmental pollutants, as well as require no oiling.

What are Harley belts made of?

The belt on a motorcycle final drive is made of high tech compounds, rubber, and kevlar.

How long do motorcycle belt drives last?

100,000 km

Are belt drive motorcycles any good?

For maximum efficiency, a belt drive is the right way to go. Even if it’s only marginally more efficient than a chain drive, it will take less energy to turn a properly fitted belt rated for the same power. Shaft drives come up last with their high weight and heavy gear oil.

What year did Harley go to belt drive?

From 1992, rubber tooth-belt drive was adopted for all Harley-Davidson streetbikes.

Is Harley a chain or belt?

Harley transitioned its product range from chain to belt drive between 1980 and 1992. Compared with a chain, belts are cleaner, lighter, cheaper, smoother, quieter and require less maintenance or adjustment than chains.

Are all Harley Davidson belt drive?

Since ’92 all Harleys are belt driven but there are still plenty of old chain driven Harleys on the road.

Are any Harleys shaft drive?

Harley has only built one model that was equipped with shaft drive, the 1942 XA. Only 1000(maybe 2000 complete models, but that’s another story) and 100% replacement parts were ever built. Harley has only built one model that was equipped with shaft drive, the 1942 XA.

Is chain or shaft drive better?

The major benefits of shaft-drive are lower maintenance and running costs, and cleanliness. Chain-drive bikes need their chains adjusting regularly and they can be expensive to replace when they wear out. They need lubricating often, especially in bad weather, which can be messy and inconvenient.

Is belt drive better than Chain?

It is evident that the two drives function the same way, but a chain drive is more durable than a belt drive. Unlike belt drives, chain drives can lift and move more massive doors, which is why many prefer it. Chain drives are best for steel carriages and not suitable for less heavy door models.