How do you fix knotter problems?
Check the knotter cam gear for wear and repair or replace as necessary. Twine tension is not correct because of a bottom Clean the bottom slacker arm and shaft. Check for slacker arm not rotating freely on the shaft obstructions. Dull or damaged twine knife Sharpen or replace twine knife.
How does a knotter work on a hay baler?
The single knotter holds the twine in the twine disc or twine holder while baling. The double knotter does not have any twine in the knotter while building the bale. Rather, it ties one knot to finish off the bale it just completed, followed by a second knot to start the next bale in the chamber.
How strong is baling twine?
Twine is measured by knot strength, which indicates the amount of force it takes before the knot breaks in the machine. “The knot strengths are starting out at 130 knot for small square bales, and they go from 130 to 170, to 210, and those are basically all knot strengths for small square bales,” he says.
How much horsepower does it take to run a small square baler?
A small square baler NH 271 or older, or JD T14 or T24 take about 15 hp to keep running. Also takes about 10 hp to pull it. Also takes about 5 hp to pull a hay rack.
Is a New Holland 310 a good baler?
Overall functional performance of the New Holland 310 baler was very good. Average feedrates varied from 2 to 8 t/h (2.2 to 8.8 ton/h). The New Holland 310 was capable of producing firm, well formed bales. Length of the 356 x 457 mm (14 x 18 in) bales could be adjusted from 305 to 1320 mm (12 to 52 in).
Do round balers have Knotters?
Don’t round balers have knotters similar to square balers.
How much horsepower do you need to run a round baler?
The MegaWide models that require a minimum of 125 PTO HP need to be paired with a more heavy duty tractor like a 4WD or Row Crop tractor….John Deere Baler Horsepower Requirements.
| Model | PTO HP (Minimum) |
|---|---|
| 450E | 55 hp |
| 450M / 450M Silage | 55 hp |
| 550M / 550M Silage | 55 hp |
| 460M / 460M Silage | 65 hp |
How much horsepower does it take to run a hay baler?
Most standard square balers on the market require 35 horsepower at your tractor’s PTO, and a minimum tractor weight of around 3000 pounds. That means that they cannot be run with today’s compact tractors. Usually it takes AT LEAST 55 PTO horsepower to run a round baler.
What is the best round baler on the market?
What is the best round baler for your farm?
- John Deere 459 Round Baler.
- John Deere 469 Round Baler.
- John Deere 559 Round Baler.
- John Deere 569 Round Baler.
- John Deere 569 Silage Special Baler.
- John Deere 854 Silage Baler.
- John Deere 569 Premium Round Baler.
- John Deere 469 Premium Round Baler.
How long will a round baler last?
most balers can last 10 to 12yrs.an that is with routine maintence. the custom balers put 10,000 to 12.0000 through them in 1 or 2yrs.
How many bales will a roll of wrap do?
Some suppliers suggested how many bales a roll of silage wrap should typically cover. The estimates ranged from 28 to 32 bales per roll, based on four layers per bale (rather than six). Some stated that a roll of wrap would do 21 to 23 bales if extra coverage is needed for each bale, as is recommended in some quarters.
How many round bales can you get out of a roll of net wrap?
On an 8000 ft roll I usually get about 165 5×6 bales out of one roll.
Is it worth wrapping dry hay?
Wrapping dry hay allows farmers to protect feed from the weather without building more structures. Some farmers believe that more layers, up to six, are well worth the extra cost. A thicker barrier is more dependable than a thin one, but more costly.