How do you reset the oil light on a 2009 Ford f350?

How do you reset the oil light on a 2009 Ford f350?

With Message Center

1. Turn the ignition to the “RUN” position.
2. Use the controls on the left of the steering wheel to scroll through menu.
3. Press the up and down arrow buttons to select “SETTINGS” and then “VEHICLE”.
4. Select “OIL LIFE RESET %” and then “OK” to reset.

How do you reset the oil light on a Ford E350?

Reset oil service light Ford E 350 Series

1. Switch the ignition ON, do not start the engine.
2. Press and release the SELECT/RESET stem to display “OIL LIFE = XXX% HOLD RESET = NEW”.
3. Press and hold the SELECT/RESET stem for two seconds and release.

How do you reset the oil light on a Ford E Series?

To reset the oil life monitoring system do the following:

1. Switch the ignition on.
2. Fully press the accelerator and brake pedals at the same time.
3. Keep the accelerator and brake pedals fully pressed.
4. After three seconds, a message displays confirming the reset procedure is in progress.

How do you reset oil life on 2009?

Turn the ignition to run (one position before starting engine). Press the SELECT/RESET button repeatedly until the engine oil life indicator is displayed. Press and hold the SELECT/RESET button for more than 10 seconds. The engine oil life indicator and the maintenance code(s) will blink.

How do you reset the oil light on a 2009 Saturn Aura?

How to Reset Oil Life: Saturn Aura 2007-2009

1. 1-Turn the ignition to run (second position)
2. 2-Press the INFO button to scroll until the Oil Life displays.
3. 3-Press the INFO and RESET (arrow) buttons on the steering wheel at the same time to display OIL LIFE RESET.

How do you reset the maintenance light on a 2009 Ford Fusion?

2008-2009 Models Do not start the engine. For turn key ignitions, press both the gas and brake simultaneously for about 20 seconds. For push button models, press and hold the button and the gas pedal simultaneously for about 20 seconds. The display will say “Resetting Oil“.

How do you reset the oil change light on a 2011 Ford Focus?

How To Reset Ford Focus Oil Change Light in 5 Easy Steps!

1. Turn the ignition to the ON position without starting the engine.
2. Simultaneously press the accelerator and brake pedals and hold them in the fully pressed position.
3. After 3 seconds, the message center displays “Service: Oil Reset In Prog”

How do I turn off MyKey speed limit?

How To Disable Ford MyKey

1. Start the car.
2. Locate your steering wheel-mounted information display controls.
3. On the main menu, select “Settings” by pressing “OK.”
4. Under “Settings,” scroll to the option that says “MyKey,” then press “OK.”
5. Under “MyKey,” search for the option that says “Clear MyKey.”

How do you reset the maintenance light on a 2010 Ford Fusion?

For 2010-2012 Ford Fusion

1. Turn on the car. So you can do this with the engine on.
2. Go to the OIL LIFE screen. Next, you’ll hit the setup key a couple of times which will get you to the oil life menu.
3. Press and hold the RESET button.
4. Turn the ignition off and then start the engine to verify the indicator has been reset.

How do you reset the oil light on a 2010 Ford Focus?

To reset oil in a 2010 ford focus, turn the ignition to the on position without starting it. Then, press the brake and gas pedals fully. After a few seconds, a message will be displayed saying oil reset in prog.

How much oil does a 2010 Ford Fusion take?

Capacity: 5.3 quarts (with filter)After refill check oil level.

Does a 2010 Ford Fusion need synthetic oil?

Recommended oil for my 2010 Fusion Get the best synthetic oil for your Fusion. With filter 5 quarts After refill check oil level. AMSOIL OE Synthetic Motor Oil is specially made for the extended oil change intervals recommended for your 2010 Ford Fusion 2.5L.

What kind of oil should I put in my 2010 Ford Fusion?

SAE 5W-20 oil

How much oil does a 2010 Ford Fusion v6 take?

Capacity: 6 quarts (with filter)After refill check oil level.

How do you check the transmission fluid on a 2010 Ford Fusion?

Open the hood (with the engine running). Locate the transmission dipstick, pull it out and wipe it off. Reinsert the dipstick and pull it back out. Make sure that the fluid is within the hot operating temperature range.