How does send and return work?
the send and return is for the effects loop, if you jack a cord out of the send jack and through some pedals and then back to the return those pedals will work beneath the amps ordinare controls, you can also use the send jack to plug in a recording device as you said.
How does an effects send work?
A send effect works by ‘tapping off’ some of a channel’s signal, and sending that to its own channel in the mixing desk. The most commonly used example is reverb: using a reverb as an insert effect will sound great, sure, but it’ll only sound great on one part.
What is the FX loop on an amp for?
An effects loop is an input/output that allows you to place effects between the pre-amp section of the guitar – where it gets its tone and the power section of the amplifier – where it amplifies the sound. This means that your pre-amp can go anywhere in the signal chain rather than having to be the last stop.
Should I use effects loop on my amp?
So if you decide to use the loop, what effects should you put in it? The general consensus is that time based effects (e.g. delay, flange, chorus etc) sound better in the effects loop whilst dirt effects (e.g. overdrive and distortion) and compressors work best in front of the amp.
What is the 4 cable method?
The 4 cable method is a way to hook up a pedalboard to an amp in a way that allows you to control which pedals or effects are placed before the pre-amp and which pedals or effects are placed after the pre-amp in the amp’s effects loop. This is achieved using four cables hence the name.
What order should you put your guitar pedals?
Dynamics (compressors), filters (wah), pitch shifters, and Volume pedals typically go at the beginning of the signal chain. Gain based effects such as and overdrive/distortion pedals come next. Modulation effects such as chorus, flangers, phasers typically come next in the chain.
How do I run an effects loop?
Using An Effects Loop Send is a signal being sent out of your amplifiers preamp. From here you will connect this to the input of the first pedal you want to add in your FX loop. Return is the signal returning to your amps power stage. The cable leaving the last pedal in your loop will plug in here closing the loop.
Do you put a looper in the effects loop?
In this setup, the looper will capture the exact pedal setup at that moment within the loop and won’t react to any changes you then make on your board. You can also put it in between effects depending on what sound you want it to capture.
Can you run distortion through effects loop?
Tonal foundation (overdrive, distortion, fuzz) Much as reverb and delay almost always work better in the loop, your dirt boxes almost always sound better in front of the amp. This is thanks to the way the amp’s compression rounds off the harsh top end of these effects. Technically, you can use them in the loop.
What is the difference between distortion and fuzz?
Whereas an overdrive takes your original tone and pushes it harder, a distortion pedal changes the sound completely and saturates the signal. Fuzz is a more aggressive style of compressed distortion. It achieves the sound by heavily saturating and clipping your signal.
When would you use an effects loop?
If the distortion/overdrive is coming from the amplifier itself, using the effects loop allows you to place effects, such as delay, reverb, and rotary speaker, after the distortion. This normally results in a better result — running a delay into the front of a distorted amp can result in a muddy, messy sound.
What comes first overdrive or distortion?
Generally, guitarists with an array of pedals like to put their drive pedals first. This includes your overdrive, distortion, fuzz, or boost pedals. Putting a delay pedal before distortion means that the echoes from the delay pedal would themselves become distorted, resulting in an unnatural and messy sound.
Which is better overdrive or distortion?
Overdrive is mild/medium; distortion is spicier — and hotter! Another difference is this: while an overdrive pedal pushes your signal pretty darned hard, it doesn’t change your existing tone much. Distortion pedals, on the other hand, not only add more saturation (or spice), but they also tend to alter your sound.
Do I need both overdrive and distortion?
Yes, overdrive and distortion can be used together, this is known as gain-stacking (adding more than one pedal that adds gain). If you use both together and have your distortion too high, it’ll usually just mask the overdrive effect. Different overdrive and distortion pedals affect the tone in different ways.
Is Tube Screamer distortion or overdrive?
The Tube Screamer is an overdrive pedal, and not a distortion pedal. It adds grit and crunch to your tone and is popular with classic rock, indie and blues guitarists. Distortion pedals on the other hand are more aggressive and suit heavier styles of music.
Is gain the same as distortion?
The gain unit would focus on increasing the size of your guitar signal as much as possible without changing its tone. The distortion pedal would focus on changing the sound as much as possible with little regard for the original signal.
What’s the difference between a fuzz pedal and a distortion pedal?
What Is the Difference Between Overdrive, Distortion, and Fuzz? An overdriven tube amp creates distortion, but in the world of effects pedals, distortion stompboxes tend to be a bit more intense than overdrive stompboxes. Fuzz is a special type of distortion where harmonic overtones dominate the overall sound.