How far apart are loading docks?
The most common dock arrangement is a flush wall with doors spaced on at least 12′ centers (Figure 1). If special trailers frequent the facility, door spacing may need to be increased. Twelve-foot centers allow for an overall truck width of 10′ including side mirrors. Narrower spacing is possible when room is limited.
What is the standard loading dock height?
48 to 52 in
What height is a truck dock?
Truck beds typically stand anywhere between 40-60 inches. In order to accommodate the different sizes of trucks, loading docks are usually built with a height between 42-56 inches and they use a dock plate or dock leveller to allow forklifts to easily enter and exit trucks.
What means loading dock?
chiefly US. : an area at the side of a building where goods are loaded onto and unloaded from vehicles.
What is the purpose of loading dock?
A loading dock, also called a loading bay, is an area of a warehouse or other building where a truck or other vehicle loads or unloads material. They are typically designed to facilitate efficient interaction with a specific type of vehicle or range of vehicle types.
How much does it cost to install a dock leveler?
There are numerous considerations when pricing a dock leveler. Budget $7,500 for a leveler from a reputable manufacturer. Cheap levelers come at a HIGH cost to your facility.
How does a hydraulic dock leveler work?
A hydraulic dock leveler: The push-button controls raise the leveler and extend the lip. As the buttons are released, the platform then floats down to the trailer floor. A hydraulic dock leveler tends to operate in a range between 12 inches below and 12 inches above the level of the dock.
What is an edge of dock leveler?
EDGE OF DOCK LEVELERS ARE PERFECT FOR TRAILERS WITH A LIMITED WORKING RANGE. Kelley Edge of Dock Levelers are platforms mounted to the edge of a building wall to assist loading and unloading of trailers in a limited working range of 3″ (72.6 mm) above to 3″ (72.6 mm) below dock.
What is a dock leveler?
Dock levelers bridge the gap and height difference between the dock and the trailer. They also compensate for the up and down float of the trailer bed during loading. A dock leveler includes a ramp (hinged along its rear edge) and a lip (hinged at the front of the ramp).
How often should dock leveler be serviced?
every 90 days
What is hydraulic dock leveler?
Hydraulic levelers are the easiest to operate and lowest maintenance available. They’re also the safest loading dock choice, as these levelers contain in-line velocity fuses to prevent free fall in a truck pull-out situation.
How is dock leveler capacity calculated?
A simple guideline exists to calculate the safest dock leveler capacity for light to normal usage. Add the gross weight of the vehicle and the gross weight of the load. Multiply that by 2.5 (ie. 8,000 lbs. forklift gross weight + 4,000 lbs gross load = 12,000 lbs x 2.5 = 30,000 lbs; rounded up to 30,000 lbs).
How much does a dock leveler weigh?
Many of our customers prefer a mechanical dock leveler rather than a hydraulic model. Our mechanical dock levelers have the same weight capacity (27,000 pounds), but are lighter, with the smallest mechanical leveler weighing in at 1,225 pounds (6′ x 6′ dock leveler) up to 1,650 pounds (7′ x 8′ dock leveler).
How much weight can a dock plate hold?
Typically capacity rating for dock levelers range from 25,000lbs. to 80,000lbs. Over 90% of all dock leveler installations fall within this capacity range. It is important to understand that this rating is a static rating.
How much weight can a dock hold?
How much weight can docks hold? Roll in and sectional docks can hold 30 pounds per square foot. A 4×16 dock is 64 square feet X 30 pounds = 1920 pounds spread evenly over the dock. For floating docks, dock capacity varies depending on the size of floats.
How high should dock be above water?
In general, a dock height at the top of less than 12″ above the water is probably about the minimum. Some people like their docks very high, but 24″ above the water would be an awful lot. Carry the section to the water, by standing in the middle and holding both sides.
How many 55 gallon drums do I need for a dock?
Building a Floating Dock with 55 Gallon Drums 4 55 gallon closed-head plastic shipping drums. 4 2×8 treated boards, 8′ long, for outer frame. 7 2×4 treated boards, 8′ long, for inner frame. 17 1×6 treated boards, 8′ long, for decking.
How do you attach a floating dock to the shore?
Gangways are the best way to attach your floating dock to the shore or a connecting ramp. A gangway is a long platform, often with handrails, that spans the distance between land and your dock.