How many BTUs do I need for a 2000 square foot house?

STEP 1: Determine how many BTUs of heating and tons of AC you need

House Square Footage	BTUs Needed
1,200 – 1,400	23,000
1,400 – 1,500	24,000
1,500 – 2,000	30,000
2,000 – 2,500	34,000

What size furnace do I need for a 2000 square foot house?

A mid-sized home of 2,000 square feet would need approximately 50,000 to 60,000 Btu to heat it properly. With a less efficient furnace operating at 80 percent efficiency this would require a 60,000- to 72,000-Btu furnace.

How do you calculate heating requirements for a house?

The calculation is as follows:

Floor’s area: 12*6.5=78 square metres.
Volume: 78*3.2=249.6 cubic metres.
The value of required thermal power: 249.6*40W=9984 watts.
Four windows will add another 400 watts, and two doors will add another 400.
Since it is a house, we use a heating coefficient of 1.5: 10.784*1.5=16,176 watts.

How many BTUs do I need to heat a room calculator?

Chart of Recommended Heating BTU Per Square Foot

Room/Area Size:	Examples:	Ave. Recommended BTU:
100-200 sq ft	Small den or office	4,000-8,000 BTU
200-300 sq ft	Den, office, small bedroom	7,000-15,000 BTU
300-400 sq ft	Efficiency apartment	12,000-18,000 BTU
400-500 sq ft	Studio/1-bedroom apartment, Tiny house	15,000-24,000 BTU

How many square feet will 5000 BTUs heat?

BTU Chart Based on Room Size
Room Size	BTU’s Needed	Room Size
150 sq. ft.	5,000 BTU’s	700 sq. ft.
250 sq. ft.	6,000 BTU’s	1,000 sq. ft.
300 sq. ft.	7,000 BTU’s	1,200 sq. ft.

How many BTUs do I need for my range?

As reported in the New York Times primer, Your Stove Just Needs to Vent, “the rule of thumb for gas stoves is that the range hood needs to remove 100 cubic feet per minute for every 10,000 BTUs of burner output.” This means a gas stove with 50,000 BTUs of total burner output requires a range hood that can accommodate …

How many BTUs do I need for a 40 gallon water heater?

34,000 BTUs

How many BTUs Do I need to boil water?

A BTU (British Thermal Unit) describes the amount of energy to raise 1 lb of water 1 degree Fahrenheit in one hour. Water equals 8.3 lbs per gallon. To boil one gallon of water starting 70°F in 1 hour you will need 8.3 x (212-70) = 1,178.6 BTUs.

How many BTUs do I need to cook a wok?

Most modern stoves have a range of gas rings, and usually one (near the front) that’s bigger than the rest. Sometimes it’s even called a ‘wok burner’. Your stove wok burner produces about 12–15K BTU.

Is 20000 Btu enough for wok?

Wok burners are a solution to the problem of supplying enough heat to duplicate true Asian wok cooking. Wok burners can generate 20,000 BTU’s to 100,000 or more BTU’s, which is more than adequate for heating a wok. Wok burners can use propane fuel for cooking and are very economical if correctly adjusted.

How many BTUs do I need to deep fry?

Single and double burners are readily available at any good outdoor outfitter. But be sure you get a unit with something in the neighborhood of 30,000 B.T.U.’s. This provides enough juice so that when frying, you can get oil back up to heat very quickly.

How many BTUs do I need to fry fish?

Look for 80 – 100 BTUs per square inch of cooking space. The more BTUs a model has, the faster it will burn up your fuel, so it is wise to only go for a grill with the amount of BTUs you need to get the job done. The answer is yes! 30,000 BTU burners will fry fish.

Is it safe to deep fry on a gas stove?

Can you deep fry on a gas stove? It won’t catch fire, but it will burn your food. Probably the most important thing to keep in mind is that water and hot oil makes a grease fire. Avoid putting anything too watery into the deep fryer, make sure to scrape off frost if you’re frying something frozen.

How many BTUs does it take to fry a turkey?

Use special turkey-frying equipment to avoid accidents. Here’s what you’ll need: A 130,000 to 165,000 BTU burner: A high-powered burner is necessary to heat the oil. A large, narrow fryer-steamer pot: This is the most oil-efficient, economical option.