How much does it cost to install a radio in a car?
Some car shops and electronic stores will be extremely cheap, while others will be thoroughly expensive. Typically, though, the cost ranges from $25 to $100. If you install the radio manually, the price may go below $25.
How do you hook up a sound system to a factory radio?
The best way to connect it to a factory system is to tap into the stereo’s speaker outputs for the amp’s input signal. Then send the amp’s outputs back to the stereo’s harness, and on to the speakers through the factory wiring.
Do you need an aftermarket stereo for subs?
You won’t get the exact same sound quality from your subwoofers as you would if you had an aftermarket stereo (like Alpine or Kenwood) in your car. The reason is that you’re not enhancing the voltage of the stereo, and therefore aren’t giving it the proper “juice”.
Can I connect subs to a stock radio?
If you are adding an amp and sub to a factory premium sound system with it’s own stock subwoofer, you must get your signal for the line output converter from that subwoofer. Adding an amp and subwoofer to a stock radio can be the easiest way to improve your stereo system in your car, if you do it correctly.
Do I have to bypass factory amp?
Bypassing the factory amp takes a little more work because you have to run the bypass harness to the factory amp, which is often located in some other part of the car. It’s usually worth the extra effort because you’ll get better sound from your new stereo, even if you’re keeping those factory speakers.
How can I make my car speakers louder without a amp?
How to Make Car Speakers Louder Without AMP?
- Use a subwoofer. One of the most effective ways of increasing the volume of your car loudspeakers involves investing in a subwoofer.
- Use sound dampening materials.
- Replace the speakers.
- Replace the cables.
- Tune it properly.
- Fine-tune the crossover controls.
- Get quality audio files.
Where is the factory amp in a 2008 Pontiac g6?
To get full-range sound, you’ll need to install an aftermarket stereo and bypass the factory amp, which is located in the right rear of the trunk.
What size speakers are in a Pontiac g6 2008?
Speakers that fit your 2008 Pontiac G6*
| Speaker location | Speaker sizes** |
|---|---|
| Front Door Midranges | MIDRANGE |
| Front Door Tweeters | Tweeter |
| Front Door Woofers | 6-3/4″ |
| Rear Deck Corners | 2 ohm 6×9″ |
What is a Monsoon sound system?
Monsoon is a brand of loudspeakers, originally automotive speaker systems and later computer speakers. Monsoon was originally associated with OEM-sourced automotive audio speaker systems, notably supplied on a number of General Motors products and then later expanded onto other manufacturers such as Volkswagen.
How do I connect my Sony Xplod amp?
How to Hook Up a Remote Wire to the Sony Xplod
- Connect a lead to your Xplod head unit’s “Remote” terminal. It could be a separate terminal, or it could be a jack located on a larger wiring harness.
- Route the remote wire to your Xplod amplifier.
- Trim any extra wire length once you finish routing it to the amplifier.
How do I set up an Autotek amp?
Connect the power cable to the positive battery terminal. The power cable must be fused within 18 inches of the battery terminal. Re-connect the negative battery terminal making sure it is securely tightened. Using spade terminals,connect the speaker cables to the speaker output connectors.
What does REM stand for on a subwoofer?
Rem = Remote Amp turn-on. This is generally a BLUE wire (no stripe) that comes directly from your headunit. In some instances you can use the ‘ANT’ or Antenna lead from your head unit.
What color is the remote wire on a Sony stereo?
Re: What colour is the remote wire on a sony xplod 52wx4… The blue/ white wire is the remote output for external amplifier or electric antenna trigger.