How much wood could a wood chuck chuck if a wood chuck could chuck would?

How much wood could a wood chuck chuck if a wood chuck could chuck would?

New York state wildlife expert Richard Thomas found that a woodchuck could (and does) chuck around 35 cubic feet of dirt in the course of digging a burrow. Thomas reasoned that if a woodchuck could chuck wood, he would chuck an amount equivalent to the weight of the dirt, or 700 pounds.

Can a groundhog chuck wood?

While woodchucks do not “chuck” wood, they do “chuck” dirt as they build underground burrows. Woodchucks do not chuck wood. But if they did, the answer is a not very tongue twister satisfying 700 pounds.

How much wood could a beaver chuck if a beaver could chuck wood?

A beaver dam. From the size of this dam, and the rate of construction (one night) you can figure out how much wood a beaver could chuck, and from that how much a woodchuck could. A reasonable assumption, is that a wood chuck would chuck about 1/5 as much wood as a beaver does.

Is Chuck a word?

chuck noun (PERSON) a friendly form of address: “All right, then, chuck?”

Why does Charles become Chuck?

The name Charles in Middle English (circa 1150–1500) was Chukken. That’s where the nickname Chuck stems from. Normans added -kin to a name when they wanted to make a diminutive (a small John). Jen was their word for John so little John became Jenkin.

What is Chuck capacity?

The capacity or size of a chuck refers to the maximum size of drill bit that it can hold. So a brace that has a chuck with a 13mm (1/2″) capacity can secure a drill bit with a maximum shank size of 13mm (1/2″).

Does Chuck Size Matter?

Figure out the size of chuck that you need. The chuck is the slot where the drill bit is inserted, so the size of the chuck limits the size of the bit you can use. Available chuck sizes are 1/4 inch, 3/8 inch and 1/2 inch. A good size for most homeowners or hobbyists is 3/8 inch. Chucks are keyed or keyless.

How do I know what size chuck key I need?

How to Size Chuck Keys

1. Look closely at the chuck on the drill for the engraved numbers. The chuck size looks something like: 1/4, 3/8, 1/2 etc.
2. Measure the diameter of the hole on the side of the chuck in inches with a ruler.
3. Take these two dimensions to your local hardware store to make your selection.

What are the types of Chuck?

Following are the different types of chucks used in lathe machine:

• Four jaws independent chuck.
• Three jaws universal chuck.
• Combination type chuck.
• Magnetic type Chuck.
• Collet chuck.
• Air or hydraulic operated chuck.
• Drill Chuck.

What is the best Chuck for woodturning?

Now it’s time to look at 5 of the best wood lathe chucks on the market in 2017.

1. TOP PICK: PSI Woodworking CSC3000C Barracuda Wood Lathe Key Chuck System.
2. NOVA 48232 G3 Reversible Wood Turning Chuck.
3. Delta Industrial 46-461 Reversible Nova G3-D Woodturning Chuck.
4. Woodstock D4054 3-Inch 4 Jaw Chuck 1-Inch by 8 TPI.

What is the function of Chuck?

A chuck is a specialized type of clamp used to hold an object with radial symmetry, especially a cylinder. In a drill or a mill, a chuck holds the rotating tool; in a lathe, it holds the rotating workpiece. Chucks commonly use jaws to hold the tool or workpiece.

What is a chuck key used for?

A chuck key or wrench is a tool that is made for the purpose of tightening or loosening the jaws of a chuck. A chuck is a type of clamp that is used to hold a cylinder object.

What is the difference between a keyed or keyless chuck?

Keyed chucks offer the advantage of applying additional torque on the bit when slippage is a concern during heavy-duty applications. Keyless chucks are engineered to quickly loosen and tighten a tool on the chuck collar of the drill, either by manual operation or when torque is applied.

Are drill chuck keys universal?

Use one universal chuck key for multiple drill chucks. The chuck key fits the most popular chuck sizes and the ratchet action provides fast, easy adjustment of your drill chuck. The dual head is reversible to handle 3/8 in. and 1/4 in.

How do you tighten a keyed chuck?

Then the chuck should be tightened by starting at one hole in the chuck and going around it, putting the chuck key in each hole consecutively and tightening it little more each time until it is tight on the drill. He does it by putting the key in one hole and turning it until it’s tight on the drill.

Why does my drill chuck slip?

Circular wear marks on the bottom of drill bits are a key indication of the drill bit slipping inside the drill chuck. The main reason for this problem is cutting fluid or lubricants used come in contact with the chuck, when this happens tightening the chuck will only go so far.

Is it necessary to tighten all three positions of the chuck?

You quite rightly point out that having 3 or 4 holes around a chuck is not an invitation to tighten all of them at every position. It is simply done to ensure that you can have nearby access for the key at any point of it’s circumference, or perhaps to overcome an obstruction to your hand.

How do you free a stuck keyless chuck?

First you have to remove the chuck assembly from the drill. To do this, put the drill assembly in a vice. Tighten the vice around the front of the chuck first. Turn counter-clockwise using a large pair of Channellock pliers around the large part of the chuck assembly – the bit should then come out.

How do you unstick a Dewalt drill chuck?

Make sure the jaws open wide enough to accommodate the size of the drill chuck. On the drill, one Vice grip on the bottom of the hand-tighten part of the chuck. Stick the other Vice grip on the top part of the chuck. Set the drill to reverse, as this is how the chuck opens.

How does a keyless chuck work?

When you insert it into a hole on the chuck, it creates a gear system that allows you to tighten or loosen it. Instead of using a key, all you have to do is twist the chuck until you feel it tighten down on your bit and start drilling. Most have a ratcheting action that you can feel as it tightens.

Why does my drill stop spinning?

Make sure the chuck is tight and ease up on the pressure your putting on the drill. If you putting too much pressure on the drill without the drill spinning fast enough it will bite into the wood and stop moving, and can damage the drill bit shank the part of the drill with out flutes).