How should a passenger be pulled back onto a small boat?

How should a passenger be pulled back onto a small boat?

Turn your boat around and slowly pull alongside the victim, approaching the victim from downwind or into the current, whichever is stronger. Stop the engine. Pull the victim on board over the stern, keeping the weight in the boat balanced, especially in small boats.

What is the first action you should take if a passenger falls overboard?

Use a buoyant heaving line: Throw the buoyant heaving line so that it lands behind the victim. Slowly pull the line towards you so the victim can grab onto it. Pull the victim to the side of the boat and assist them back into the boat.

How do you recover someone on overboard?

If someone falls overboard, immediately:

1. sound the alarm, turn bow in the direction of the person overboard, stop engines, throw a buoyant object to assist the person and mark the position.
2. assign one person to constantly keep the person in the water in sight.
3. manoeuvre the vessel carefully to pick the person up.

What to do if someone falls off a boat?

What to Do If Someone Falls off Your Boat

1. Yell “Man Overboard”
2. Stop the Boat.
3. Hit the MOB Button.
4. Throw a Flotation Device.
5. Assign Crew Roles.
6. Navigate Back to the MOB.
7. Retrieve the Man Overboard.
8. Contact Emergency Services.

Where is the best place on a boat to bring a person who has fallen overboard?

As soon as someone notices a person falling into or flailing in the water, he or she should point to the individual and shout “Man Overboard!” followed by “Port Side!” or “Starboard Side!” depending on whether the person is on the left (Port) or right (Starboard) side of the boat.

What can a vessel operator use to make sure?

Make sure all boat operators have a Pleasure Craft Operator Card or other proof of competency on board. Check your charts to be sure you know the locations of local hazards and the expected water levels and tides. Leave a float plan with a reliable friend or relative.

What type of fire extinguisher is required on a motorized pleasure craft?

C fire extinguisher

Do all pleasure crafts need a bailer?

Note: A bailer or manual bilge pump is not required for a pleasure craft that cannot hold enough water to make it capsize or a pleasure craft that has watertight compartments that are sealed and not readily accessible.

What are 2 types of acceptable lifebuoys?

Lifebuoys must be at least 610 mm (24”) in diameter. SOLAS lifebuoys are 762 mm (30”) in diameter. Smaller lifebuoys and horseshoe-type devices are not approved. The lifebuoy must be attached to a buoyant line of not less than 15 m in length which must be securely fixed, and in good condition.

Who approves the lifebuoy required to be kept on board a pleasure craft?

Approval of Life-Saving Appliances 7 (1) A personal flotation device, lifejacket, lifebuoy, self-igniting light, pyrotechnic distress signal or life raft required by these Regulations shall be of a type that is approved by the Minister and shall bear a mark or label indicating the approval.

What are three characteristics that a buoyant heaving line must have?

Be at least 610 mm (24 inches) in diameter and be made of inherently buoyant material and… Be attached to a good-quality buoyant line that won’t kink and is at least 9.5 mm in diameter and 15 metres long and… Have a Transport Canada approval stamp or label with an approval number in the following format: T.C.

What is the purpose of a buoy heaving line?

This buoyant heaving line is used to be thrown toward a person in distress in the water. To improve the accuracy of the throw overboard to a person overboard, a balloon or other floating object should be fixed to the buoyant heavy line.

What is the minimum buoyant heaving line?

The requirements for buoyant heaving lines and lifebuoys depend on the length and type of pleasure craft you are operating. Sailboats and powerboats 6 metres (19.7 feet) or less in length must have a buoyant heaving line that is at least 15 metres (49.2 feet) in length.

What is a pleasure craft courtesy check?

Pleasure Craft Courtesy Check is a FREE service provided by the Canadian Coast Guard Auxiliary to assist you, the owner of a small craft vessel up to 20M, in maintaining your vessel´s safety equipment at standards acceptable to the marine environment.

What determines the number and type of distress flares required on board a pleasure boat?

There are four types of approved pyrotechnics: Rocket Parachute Flare (A), Multi-Star Flare (B), Hand Flare (C), Buoyant or Hand Smoke Signal (D). The number and type of distress flares required on board a pleasure boat depends on the length of the vessel, the type of vessel, and the area of operation. …

Where is the best place to install a radar reflector?

It should be installed in an area where it is a minimum 4m (13.1 ft) above the waterline and higher than all the surrounding superstructures to insure that you’ll be seen on the radar screen of large ships and fishing boats. Height is also very important.

Where is it safe to operate a fuel burning appliance in a pleasure craft?

at each access to any space where a fuel-burning cooking, heating or refrigerating appliance is fitted; at the entrance to any accommodation space; and. at the entrance to the machinery.

Which of the following is required to be carried on board your boat at all times?

Boat operators are required to carry at least one life jacket or personal flotation device (PFD) for each person on board the boat.

What is considered the appropriate action to take in the event a boat springs a leak?

If the impact caused a leak: Have everyone leave the pleasure craft if you are grounded on land. Drop anchor or use some other means to keep your pleasure craft where it is. Use a bailer or bilge pump if necessary to keep your pleasure craft from sinking.

What is the fastest way to remove water from a bilge?

Centrifugal: Draw water into the pump with whirling vanes and push it out through an outlet port. The pump must be submersed in the bilge water to operate and can usually remove all but the last inch or so of water. Centrifugal pumps have a built-in strainer that can be easily removed for cleaning.

Should there be water in the bilge?

No new boat should have that amount of water in the bilge. If you have one pump in the deepest part of the bilge at rest, the amount of residual water depends on how low it can pump before the float switch kicks OFF , plus the amount of water which drains back from all uphill hose.

How do I get all the water out of my bilge?

All you really need is a pump that can run dry, and will create enough lift to get the remaining water out of the bilge. So I installed a Whale diaphragm pump, it can run dry with no problems, and creates enough suction to lift the water that is in the bottom of the bilge.

Do bilge pumps come on automatically?

Today, most bilge pumps come on automatically. This is because they are built with an automatic float switch that turns the bilge pump on when water levels in the bilge start to rise.

Should I leave the bilge pump on?

When water accumulated in the bilge the float switch would go on and stay on even though the pump itself was out of water, until eventually the battery will go dead.

Will a bilge pump run without water?

Re: Running bilge pump with no water in bilge if it heat the seal up on the shaft, it might loosen up and let water into the motor. Its not a good idea to run dry , but in most cases may not be too bad . If the shaft is greased in there might not be a problem.

How often should a bilge pump come on?

It should check for water every two minutes. Nothing should come out of the bilge unless it has been raining or you have been in rough water. Next time you have her on the trailer use a water hose to fill the bilge and watch for where it comes out of the hull. You can do this with less water if you park on a hill.