What is a 3 part CSI specification?

What is a 3 part CSI specification?

CSI’s 3-Part SectionFormat™ divides each specification document into – you guessed it – three parts: General, Products, and Execution. Within each of the three parts is a standard set of article titles set in a standard order to further organize the specification data.

How do you write specifications for a project?

Writing Specifications for Construction Contracts

1. The layout and grouping of subjects should be logical.
2. Requirements for each subject should be stated clearly, in logical order, and checked to see all aspects are covered.
3. Language and punctuation should be checked to see they cannot give rise to ambiguity.

What is construction project specification?

According to the Dictionary of Architecture & Construction a specification is, “a written document describing in detail the scope of work, materials to be used, methods of installation, and quality of workmanship for a parcel of work to be placed under contract; usually utilized in conjunction with working (contract) …

What are CSI division numbers?

Divisions

• Division 01 — General Requirement.
• Division 02 — Existing Conditions.
• Division 03 — Concrete.
• Division 04 — Masonry.
• Division 05 — Metals.
• Division 06 — Wood and Plastics.
• Division 07 — Thermal and Moisture Protection.
• Division 08 — Doors and Windows.

What is a CSI format?

The Construction Specifications Institute (CSI) is the organization that publishes the MasterFormat. This publication is the specifications-writing standard for most of today’s construction and commercial building design projects in North America.

What CSI division is insulation?

Division 07 – Roofing, Waterproofing and Insulation.

What are Division 10 Specialties?

Division 10 is a division of construction that covers specialty products and materials for projects. These are products that don’t exactly fall under other standard divisions….Division 10 can contain products such as the following:

• Storage Specialties.
• Partitions.
• Toilet Specialties.
• Safety Specialties.

What CSI division is concrete?

Division 03

What division is vapor barrier?

Division 7

Can I use plastic sheeting as a vapor barrier?

In simple terms, a vapor barrier is a material that won’t allow moisture to pass through it, such as plastic sheeting. A very simple experiment to show how a vapor barrier works is to lay a plastic garbage bag down on some damp soil. There are two basic types of vapor barriers used with exterior wall insulation.

Where do you put vapor barrier?

Vapor barriers are usually best installed on the side of the wall that experiences the hotter temperature and moister conditions: the inner surface in colder climates and the outer surface in hot, humid climates. In existing spaces, oil-based paints or vapor-barrier latex paints offer an effective moisture barrier.

Should I put plastic over insulation before drywall?

Without poly beneath the drywall, water vapor hits the drywall and diffuses through to the drier (in summer) indoor air. By installing a sheet of poly there, you cut off that drying mechanism and water that finds its way into walls can stay there longer and do more damage.

Does moisture barrier go up or down?

The air is usually warmer inside the house, so condensation can build up from air entering the wall from the inside. The vapor barrier should point toward the room in this case.

Is a moisture barrier necessary?

When moisture penetrates your flooring, it can cause mold, mildew, and the potential for water damage. A moisture barrier helps control the water vapor’s movement to help protect your floors. Therefore, if you’re installing floors in an area that sees moisture, even a little, a vapor barrier is needed.

Do I need a moisture barrier under vinyl flooring?

The rule of thumb is any vinyl over 4mm can have a vinyl specific underlayment. Vinyl floors under 4mm should be installed right over the subfloor. If you have any areas on a concrete subfloor with moisture concerns, it is recommended to use a vapor barrier underlayment that will not add any cushion to the planks.

Which side of the underlayment goes down?

Get started by rolling out the underlayment with the silver side facing down. The tape strip should be flush up against the wall. Leave the overlapping section on the side that goes out toward the room. You’ll need this section later as you continue to unroll your underlayment.

Does it matter which way you lay underlay?

Always lay out the underlay in the opposite direction to the floorboards. If you’re using foam underlay, make sure this is with the backing facing upwards and the coloured film face-down to the floor.

Which way does foam underlay go?

If you are using rubber underlay, it should be face-down so the rubber is against the floor and the backing faces up. Foam underlay should also be face-down, with the coloured film on the floor and the backing face up.

Do you nail down underlayment?

To nail down the plywood, use underlayment nails, which have a smaller head and rings on the nail shank that prevent them from working loose. Drive nails throughout the entire sheet of plywood, every 6 to 8 inches (see illustration on next page), to ensure the floor is down solidly.

Can I use brad nails for underlayment?

Brad Nails or Finish Nails: It is best to use brad nails, and fasten the 1/4 luan plywood to the carcass. It will be the glue that will hold the plywood together for the long term. The nails just hold the plywood together while you glue. The best glue that I can recommend is Titebond II.

How do you speed up underlayment?

If your choose this route, staples are a good choice to fasten the underlayment. Staples usually have a coating which help increase the holding power. Using a crown compression stapler, staple 2 inches on the seams and edges with 4-6 inches apart in the middle.

What is the best underlayment?

When installing hardwood or engineered wood flooring, the best underlay options are cork and foam. However, foam does have more give than cork so, while it is the more popular option, we recommend cork. Cork has less give, making it less likely to flex underneath your planks.

What is the thickest underlayment?

Foam is the most basic variety of underlayment. Foam underlayment comes in a variety of thicknesses from 3mm (1/8”) to 6mm (1/4”) thick and usually comes in rolls of various widths and lengths. You have the most variety of choice with foam underlay.

What does underlayment mean?

Underlayment is basically a thin layer of material that is sandwiched between other materials. The underlayment is used in two different industries, roofing and flooring.

What happens if you don’t put underlayment under laminate flooring?

If you don’t install the underlayment correctly, your laminate floors could be damaged or even ruined. In fact, some floors require an underlayment to be correctly installed in order for the warranty to be valid.

What flooring does not require underlayment?

No Underlayment – Laminate Wood Flooring – Laminate Flooring – The Home Depot.

Can you walk on underlayment?

Absolutely. If your subfloor is NOT safe to walk on then you’ve got BIG problems LOL. The subfloor is what the decorative floor is applied over and it’s the structural component of the flooring. If not slab on grade then the subfloor is laid over top floor joists.

What is the best underlayment for laminate flooring over concrete?

Best underlay for laminate flooring is foam or cork. Best underlay for laminate flooring is foam because it is simple to install, it is a good sound barrier, and is very cost effective. Some best foams have attached additional layer which functions as the best moisture barrier.