What is the main difference between switch and router?
Router and Switch are both network connecting devices. Router works at network layer and is responsibe to find the shortest path for a packet whereas Switch connects various devices in a network. Router connects devices across multiple networks.
What is the difference between switching and routing?
The main differences between Routing and Switching are as below. The function of Switching is to switch data packets between devices on the same network (or same LAN – Local Area Network). The function of Routing is to Route packets between different networks (between different LANs – Local Area Networks).
Can I use a switch instead of a router?
A network switch can be used in place of a router but is not recommended. Internet Service Providers typically only provide one public IP address resulting in only one device being able to access the Internet when a switch is used instead of a router, as well as presenting major security concerns.
Do I need a router between modem and switch?
6 Answers. Yes and no. The router provides a local network, and distributes local IP addresses to all the computers connected to it, while only using 1 external IP provided by your ISP. Without the router, that switch is going to try to give each PC on the network, it’s own external facing IP address.
Do switches have IP addresses?
Unmanaged and layer 2 network switches do not have an IP address, whereas managed switches and layer 3 switches do. A network switch with an IP address is required for Telnet which allows remote access to the switch. The IP address of a switch can be found via the router or an IP scanner.
What comes first router or switch?
Assuming a normal residential setup, you need to put the switch after the router. because the modem will only talk to the first computer that talks to it. To share the connection, you need a router. Thus, you usually want that “first device” to be a router.
Does it matter which port I use on a switch?
It does not make any difference what port you use to connect to the internet. Please note you need multiple ethernet cables, one to connect the switch to the internet, which would be either a router or another ethernet connection, and the additional cables will run from the switch to each device you are using.
Do Cisco switches have IP addresses?
If you want to be able to manage your switch remotely over the network, your switch needs an IP address. If your switch has multiple VLANs configured, and you want to be able to manage the switch from each VLAN, the switch requires an IP address on a VLAN interface in each VLAN.
Can we assign IP address to layer 2 switch?
ip address cannot be configured on layer2 switch ports. It’s feasible to configure ip address for accessing switch with management IP address VLAN can be created and assign ip address to Vlan . There is not such thing as IP on layer 2 device.
Does Layer 3 switch have IP address?
Simply put, a layer 3 switch combines the functionality of a switch and a router. It acts as a switch to connect devices that are on the same subnet or virtual LAN at lightning speeds and has IP routing intelligence built into it to double up as a router. This is how a layer 3 switch acts as both a switch and a router.
Why is VLAN trunking used?
VLAN trunking enables the movement of traffic to different parts of the network configured as a VLAN. A trunk is a point-to-point link between two network devices that carry more than one VLAN. With VLAN trunking, you can extend your configured VLAN across the entire network.
What are the advantages of VLAN?
The Real Advantages of a Virtual LAN (VLAN)
- help with network efficiency by reducing extraneous traffic;
- enhance security by creating a virtual boundary around that business unit;
- improve bandwidth performance by limiting node-to-node and broadcast traffic;
- save workplace disruption, as there is no need to physically match up ports and switches on a network.
Can two VLANs have the same IP address?
The OSA-Express Layer 2 implementation allows the hosts to manage IP addresses and ARP cache, so it is possible to have a single guest LAN segment (or VSWITCH segment) where two different hosts use the same IP Address on different VLAN groups.
Which are the 2 trunking protocols?
There are two trunking protocols used on modern communication networks: Inter-Switch Link (ISL) from Cisco and the aforementioned nonproprietary IEEE 802.1Q. Of the two, IEEE 802.1Q is the industry standard. Even Cisco switches now use IEEE 802.1Q (dot1q) by default.
Why do we use trunking?
The main purpose of trunking is to carry traffic between switches and maintain the VLAN information. Unlike an access link, the trunk link does not belong to a single VLAN but instead can carry traffic from several VLANs over a point-to-point link between two devices that understand the protocol.
How do you communicate two different VLANs without a router?
In order to perform communication between two different vlans we require a router or mls. But it is possible to provide communication between two different vlans without using any layer 3 device. This concept is based upon tagging / untagging frames.
What protocol is Trunking?
VLAN Trunking Protocol (VTP) is a Cisco proprietary protocol that propagates the definition of Virtual Local Area Networks (VLAN) on the whole local area network. To do this, VTP carries VLAN information to all the switches in a VTP domain. VTP advertisements can be sent over 802.1Q, and ISL trunks.
What is the function of wheel and trunking protocol?
Introduction. VLAN Trunk Protocol (VTP) reduces administration in a switched network. When you configure a new VLAN on one VTP server, the VLAN is distributed through all switches in the domain. This reduces the need to configure the same VLAN everywhere.
What is trunking in switch?
A trunk port allows you to send all those signals for each switch or router across a single trunk link. In contrast to an access port, a trunk port must use tagging in order to allow signals to get to the correct endpoint. Trunk ports typically offer higher bandwidth and lower latency than access ports.
What is native VLAN?
The Native VLAN is simply the one VLAN which traverses a Trunk port without a VLAN tag.
Is native VLAN required?
In order to configure native VLAN, switch port trunk native VLAN command is used. Native VLANs are recognized if they are not tagged to any trunks. It is not necessary to have native VLAN on the trunk.
Where is native VLAN used?
In short, the native VLAN is a way of carrying untagged traffic across one or more switches. Consider this Example. The ports that the hosts connect to are trunk ports, with native VLAN 15 configured. Carrying untagged traffic has its uses.
Do you need to allow native VLAN on trunk?
The NATIVE VLAN should NOT be included on the “switch allowed vlan” list. However, the NATIVE VLAN should also NOT be used for ANYTHING else. If you have a vlan defined for any device/access port, then that VLAN must be allowed on the trunk port, and should NOT be used for the NATIVE VLAN.
Is native VLAN tagged or untagged?
In Cisco LAN switch environments the native VLAN is typically untagged on 802.1Q trunk ports. This can lead to a security vulnerability in your network environment. It is a best practice to explicitly tag the native VLAN in order to prevent against crafted 802.1Q double-tagged packets from traversing VLANs.
What is the difference between native VLAN and default VLAN?
Cisco books will often refer to the “default VLAN”. The Default VLAN is simply the VLAN which all Access Ports are assigned to until they are explicitly placed in another VLAN. In the case of Cisco switches (and most other Vendors), the Default VLAN is usually VLAN 1. The Native VLAN can change.
How do I see if a VLAN is on the trunk?
Use the show interfaces trunk command to check whether the local and peer native VLANs match. If the native VLAN does not match on both sides, VLAN leaking occurs. Use the show interfaces trunk command to check whether a trunk has been established between switches. Statically configure trunk links whenever possible.
How do I add and remove VLANs to my trunk?
To remove VLANs from the allowed VLANs list for a trunk, issue the clear trunk mod_num/port_num vlans command. To add specific VLANs to the allowed VLANs list for a trunk, issue the set trunk mod_num/port_num vlans command.
Does Switchport mode trunk allow all VLANs?
The all option in the switchport trunk allowed vlan command means all VLANs, so you can use it to reset the switch to its original default setting (permitting all VLANs on the trunk).
How do you trunk a VLAN?
To enable trunk links, configure the ports on either end of the physical link with parallel sets of commands. To configure a switch port on one end of a trunk link, use the switchport mode trunk command. With this command, the interface changes to permanent trunking mode.