What kind of oil does a 2006 Honda Element take?

What kind of oil does a 2006 Honda Element take?

Mobil 1 Extended Performance Synthetic Motor Oil 5W-20 5 Quart.

What kind of oil does a 2003 Honda Element take?

Engine Oil

Viscosity:	5W-20 (All TEMPS)
Capacity:	4.2 quarts. . w/ofAfter refill check oil level. 4.4 quarts. (with filter)After refill check oil level.
Torque:	33 ft/lbs (Oil Drain Plug)

What kind of oil does a 2005 Honda Element take?

The 2005 Honda Element uses SAE 5w-20 full synthetic oil.

Can I put 5W-30 in my Honda Element?

5w-30 is fine.

Can I use 5W30 instead of 5W20 in my Honda?

Due to the increased resistance of the thicker 5W-30 oil, your engine will produce slightly lower fuel economy and horsepower output. You also risk engine damage when using 5W-30 instead of 5W-20, as the internal engine components are specifically designed to be used with 5W-20 motor oil.

How much oil does a Honda Element take?

Engine Oil Capacities: Without filter 3.4 quarts After refill check oil level. With filter 3.7 quarts After refill check oil level.

Is 5W-20 oil good?

The thicker 5W-30 should see a slight advantage when operating at higher temperatures, while the thinner 5W-20 oil should provide better engine protection at lower temperature levels and has the added benefit of slightly improving fuel efficiency.

Where is the oil filter Honda Element?

Change the oil filter It is in the back left of the engine (passenger side).

How do you reset the oil light on a Honda Element?

Turn off the engine. Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting). Hold the button for at least 10 seconds, until the indicator resets. Turn the ignition off and then start the engine to verify the indicator has been reset.

What kind of oil does a 2007 Honda Element use?

The 2007 honda element uses sae 5w-20 motor oil.

What kind of oil does a 2008 Honda Element take?

Engine Oil

Viscosity:	5W-20 (All TEMPS)
Capacity:	4.4 quarts. (with filter)After refill check oil level. 4.2 quarts. . w/ofAfter refill check oil level.
Torque:	33 ft/lbs (Oil Drain Plug)

How do you check the transmission fluid on a 2007 Honda Element?

The automatic transmission fluid level is checked (with the engine off and the car on level ground) using the dipstick (with the yellow marking) in the right end of the transmission housing. Remove the dipstick and wipe it off. Insert the dipstick and remove it.

How do you reset the oil light on a 2008 Honda Element?

Oil Change Light Reset Honda Element 2007 2008 2009 2010 2011 Procedure

1. Turn the ignition to the “RUN” position.
2. Press the “SELECT/RESET” knob until the engine life indicator is displayed.
3. Press the “SELECT/RESET” knob for more than 10 seconds, the indicator and the maintenance code(s) will blink.

How do you reset the oil light on a 2007 Honda Element?

How To Reset Honda Element Oil Life Wrench Service Light (2007-…

1. Turn the ignition key to the “ON” position without starting the engine.
2. Press the Select/Reset knob repeatedly until the “Remaining Oil Life” appears on the display.
3. Press and hold the knob until the oil life percentage begins to blink.

What does the wrench light mean on a Honda Element?

Maintenance Minder indicator

How do you reset the oil life on a 2006 Honda Element?

2003-2006

1. Turn the ignition switch to the OFF (0) position.
2. Press and hold the TRIP/RESET button(s) in the instrument panel, then turn the ignition switch to ON (II) position.
3. Hold the button(s) for 10 seconds or until the indicator resets.

How do you reset the computer on a Honda Element?

Put the key into the ignition and turn it to the “on” position but dont start the engine. The vehicles power turns on the scanner. Let the scanner read the trouble codes. Press the “reset” or similar command on the face of the scanner to reset the vehicles computer.

How do you reset the oil light on a 2005 Honda Element?

Oil Change Light Reset Honda Element 2003 2004 2005 2006 Procedure

1. Turn the ignition off.
2. Press the “SELECT” and “RESET” switches at the same time, and turn to ignition to the “ON” position.
3. Hold switches for at least 10 seconds until the indicator is reset.