What kind of transmission fluid does a 1989 Mustang take?
FRAM Transmission Fluid – Full Synthetic Dexron VI Automatic Transmission Fluid 1 Gallon (Part No. F426-1G)
How much horsepower does a 1989 Mustang 5.0 have?
1979-1993 5.0L V8 Foxbody Mustang Power Ratings
| Year | Engine (cu/L) | Horsepower @ |
|---|---|---|
| 1988 | 302/5.0L HO | 222 @ 4200 |
| 1989 | 302/5.0L HO | 220 @ 4200 |
| 1990 | 302/5.0L HO | 220 @ 4200 |
| 1991 | 302/5.0L HO | 220 @ 4200 |
How much fluid does a Mustang T5 transmission hold?
The T-5 takes 2.8 quarts.
Can you fill a T5 from the shifter?
Yes you can do it that way. You just have to do it kind of slowly, as there’s not a real big passage for it to run down through. Also, make sure the drive shaft and speedo gear are in place; otherwise you WILL have fluid everywhere.
What kind of transmission fluid does a t45 take?
use motorcraft mercon-v atf.
How much can a T5 handle?
New Member. 89 T5 is rated at 285ft/lbs, it will all depend on how it was previously used.
What is the difference between T5 and T5 world class?
There are two generations of T-5 transmissions; from beginning of production until mid-1985 these units were referred to as “non-world class” units. The most important difference between the non-world class and the world-class transmissions is the torque rating. Later is better (or the higher the tag number).
Are all Ford T5 transmissions the same?
The T5 is the longest running five speed overdrive, standard shift transmission spanning more than 30 years of production. While there are numerous configurations of the T5, because of the large quantities of T5’s produced, many parts are interchangeable.
How do I identify my Borg Warner transmission?
Look at the forward shaft bearing/support. Borg Warner transmissions usually a sticker saying Timken with a part number or a yellow and black sticker that says “use Dexron II only,” according to British V8 Newsletter. These stickers are most commonly found on Borg Warner transmissions.
Does Borg Warner still make transmissions?
We developed and introduced the world’s first high volume series production dual clutch module for automotive transmissions more than ten years ago. Today we produce over 800 thousand units annually, supporting the widest range of vehicle applications in the in the segment.
Will a Chevy T5 fit a Ford?
The Chevy version T5 WILL NOT bolt up to a Ford motor. The bolt pattern is different. The input shaft length is way different and the chevy version is canted 17* towards the drivers side.
Will a T5 bolt up to a 350?
GM did not put a T5 behind a 350 for a reason and the V6 trannys are wimpy at best. The early T5 was a pop can made to hold about 175 horsepower. It did it poorly. The later (88-92) T5 World Class held more torque, but not much.
How much torque can a Chevy T5 handle?
The T5 is rated at 350 ft lb of torque.
How do I identify a Borg Warner T5 transmission?
The Borg Warner T-5 is generally identified by a 1352-xxx number stamped on a metal tag on a tail housing bolt. This tag is normally under the second bolt from the top on the left side of the transmission. While Ford used aluminum for these tags, GM used steel which is prone to rusting.
How do you identify a Borg Warner T10?
Look for casting identification on the transmission casing. According to Drivetrain.com, the “T10” designation and the code, “13-04,” is sometimes cast on the transmission housing. Count the cross-grooves on the input shaft. The input shaft enters the engine at the front of the transmission.
How do you read a T5 transmission tag?
The tag below reads 1352-232. Each T5 case, case cover and tail housing will have a casting mark that indicates what year the part was cast. It looks like a small flower with a number in the center. The photos show several examples.