Which federal agency is responsible for regulating interstate shipments of hazardous materials?
The Hazardous Materials Transportation Act (HMTA) The Department of Transportation (DOT) has the authority to regulate the handling and interstate transportation of hazardous materials.
What is the name of the agency responsible for hazardous materials?
Hazardous materials are defined and regulated by the U.S. Environmental Protection Agency (EPA), U.S. Occupational Safety and Health Administration (OSHA), U.S. Department of Transportation (DOT), and U.S. Nuclear Regulatory Commission (NRC).
Which federal law is intended to assure so far as possible safe working conditions?
The Occupational Safety and Health Act
Which federal agency provides training resource information and technical assistance to states?
Federal Emergency Management Agency (FEMA)
What is the primary hazard associated with most flammable liquids?
Explosion
Is it difficult and sometimes impossible to purify contaminated groundwater?
The source of groundwater contamination can include surface impoundments in which hazardous materials are disposed or stored, such as ponds and lagoons, leaking underground storage tanks, or any spill where contaminants can seep downward. It is difficult and sometimes impossible to purify contaminated groundwater.
What are the five phases of a hazardous materials life?
Consider the five phases of the life cycle of a hazardous material-production, transportation, storage, use, and disposal.
What are the four routes of entry for toxic substances?
Exposure to chemicals may occur by the following routes:
- inhalation,
- ingestion,
- contact with skin and eyes, or.
- injection.
Is 5 a introduction to hazardous materials?
A An Introduction to Hazardous Materials containing correct FEMA IS 5. A answers and course notes. A very general introduction into hazardous materials that should prepare you for much more comprehensive courses in the future.
What defines a hazardous material?
A hazardous material is defined as any substance or material could adversely affect the safety of the public, handlers or carriers during transportation.
What is the primary purpose of conducting a hazardous materials exercise?
A primary purpose of conducting a hazardous materials exercise is to find out: What type of incident is most likely to occur. Which responders should receive raises. Whether planned procedures work.
What is the definition of hazardous materials FEMA?
term “hazardous materials” in a broad sense to include: Explosive, flammable, combustible, corrosive, oxidizing, toxic, infectious, or radioactive materials.
Is an introduction to hazardous materials?
A An Introduction to Hazardous Materials Kindle Edition. Identify steps individuals and communities can take to protect themselves during a hazardous materials release. Identify steps individuals and communities can take to protect themselves during a hazardous materials release.
What is the difference between control zone and control area?
The difference is that a control Zone extends down to the ground, whereas a Control Area does not. The lower limit of a control area (CTA or TMA) can be expressed as a height, pressure altitude or flight level but cannot be less than 200 m (700 ft) above the ground.
What is meant by control zone?
A control zone (CTR or controlled traffic region) in aviation is a volume of controlled airspace, normally around an airport, which extends from the surface to a specified upper limit, established to protect air traffic operating to and from that airport.
What is a control zone fall protection?
The use of a control zone is an approach to fall protection for workers performing work on a level working surface within 2 metres of an unguarded edge above a surface or thing that could cause injury to the worker if the worker were to fall on the surface or thing.
What height is fall protection?
four feet
Can you use rigging for fall protection?
If any component of the rigging system, such as a shackle, wire rope, or synthetic sling was or is used to hoist materials, these components are not be used as part of a fall protection system. If they have not been so used, they may be used as part of a fall arrest system if they meet the criteria in §1926.502.
Who can use fall protection?
The Occupational Health and Safety Regulation requires workers to use fall protection systems when they could fall from a height of 3 m (10 ft.) or more, or where a fall from a lesser height could result in serious injury.
When Must Fall protection devices be used?
When must employers provide Fall Protection? The 6-foot rule. Subpart M requires the use of fall protection when construction workers are working at heights of 6 feet or greater above a lower level.
What item is an example of fall protection?
Common fall arrest equipment includes an anchor point, body harness, and connector (such as a lanyard or self-retracting lifeline. A full-body safety harness is your first line of defense. However, the kind of harness you need will depend on the type of work being done.
What are the two types of fall protection?
Two basic types of fall protection are travel restraint and fall arrest. Both involve wearing a full-body harness.
What is the best method of fall protection?
The preferred solution to all fall hazards is elimination. The reason for exposure to the fall hazard is challenged and evaluated to determine if a change in the procedure, practice, location or equipment will eliminate exposure to the fall hazard.
What are the 3 types of fall protection?
Besides fall arrest, there are three more types of fall protection equipment:
- Positioning – These systems hold workers in place while leaving their hands free, to allow them to work.
- Suspension – These systems lower and support workers while leaving their hands free for the activities they need to perform.
What is the difference between fall protection and prevention?
It’s important to understand the differences between fall prevention and fall protection. Fall prevention refers to a system that prevents or eliminates the hazard of a fall. Fall protection refers to equipment used to mitigate or limit the effects of a fall from a height.
Which fall protection controls is better than the others?
Administrative controls. In general, it is better to use fall prevention systems, such as guardrails, than fall protection systems, such as safety nets/fall arrest devices. That’s because prevention systems prevent falls from occurring in the first place.
What is the least effective fall protection?
Personal fall arrest