Why is my radio not working in my Jeep Grand Cherokee?

Why is my radio not working in my Jeep Grand Cherokee?

Push and hold the volume and two knobs at the same time for about 10 to 20 seconds until the radio power is off. Once the system shut off it will quickly turn back on and take about a minute or so to fully come back online. After pressing yes You will have to wait 30 seconds and then there’s some will begin to reset.

How do I turn on my jeep radio?

Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. The electronic volume control turns continuously (360 degrees) in either direction without stopping.

How do I reset my Jeep Grand Cherokee radio?

Press the Voice Command and both Phone buttons (all 3 buttons) (the ones on the steering wheel) press all 3 for 30 seconds, then release. Open driver door, leave open for 30 seconds, then close the door.

How do I unfreeze my jeep radio?

Try pulling it for 10 seconds. The radio/amplifier is the M12 fuse. Pull it out for 30 seconds then put it back in. As mentioned, you can pull the fuse or just wait about 5 minutes with the jeep turned off and it will shut off.

Why is the screen in my Jeep not working?

The Jeep Grand Cherokee touchscreen not working can be due to multiple different things such as a short or disconnected power cable under the dash, a software glitch or issue, and it could also be a blown fuse or damage to the screen.

How do I reset my Jeep touch screen?

To do a soft reboot of Your touch screen in Your 2018 Jeep Grand Cherokee You’ll need to hold down the enter and volume buttons for 15 to 25 seconds. After this time has passed the screen will flash and then it should come back on and work like normal.

How do I reset a Uconnect frozen screen?

How do I reset a UConnect frozen screen? Press in and hold your volume and tuner button at the same time for about 10 seconds until the screen shuts down.

How do I reset UConnect?

For the latest Uconnect® version 8.4, this is how you can perform a soft reset of the system: Turn your key in the ignition to “Run,” but leave the car in park. Simultaneously press the volume button and the tuner knob at the same time. Continue pressing them down for 10 – 20 seconds.

Why is my UConnect frozen?

You could try removing power from radio for 90 seconds or so, so it will hard reboot. If that does not work, you could try to create a flash drive on the uconnect site and update the software. To power down radio, you need to pull the fuse that directly supplies battery feed to the radio at all times.

How do I reset my UConnect 12?

RamCares

1. Put your vehicle into the accessories mode (ACC or RUN)
2. Hold down the Phone and voice recognition buttons (or tuner and volume knob), at the same time, for thirty seconds.
3. Let go of the buttons.
4. Turn the vehicle off.
5. Open driver’s side door for thirty seconds (or until dash illumination goes black)

What to do if Uconnect is not working?

There are a few reasons why the Uconnect system will not connect properly with your mobile phone.

1. Use a compatible phone with Uconnect.
2. Verify the Bluetooth version on your phone.
3. Enable Bluetooth on your phone.
4. Turn on the car stereo and enter the Bluetooth pairing code.
5. Pair the mobile phone with Uconnect.

How do I reset my Uconnect 2020?

Five Easy Steps to Reset UConnect®

1. Ensure your vehicle is in park and in “Run” mode.
2. Press and hold down the volume and tuner knob buttons at the same time.
3. Hold down the knobs for 10 – 20 seconds.
4. After holding down the knobs, the screen should flash your vehicle brand name and then go dark.

How do I reset my RAM radio?

To begin, turn Your ignition on, but You don’t need to start the engine. Now go to the Uconnect screen and hit the button at the bottom that says “Apps” and then hit the right side arrow button. Click on “Settings” at the bottom right of the screen. Now scroll down all the way and click on “Reset”.

How do you reset the radio on a 2013 Dodge Ram?

To perform a 2013 Dodge Ram 1500 radio reset, hold down the temp up and down buttons for 5 seconds and then select radio reset. You will come into problems with the sound. This could be from the stereo’s speakers or a phone that is connected to the vehicle.

How do I reset my Dodge Ram 2019?

To reset the uconnect on the 2019 dodge ram 1500, hold the vr and phone buttons on the steering column for 30 seconds, then open the door for an additional 30 seconds. Tried both ways to reboot, neither of them worked.

How do you reset the radio on a 2012 Dodge Ram?

To perform a 2012 Dodge Ram 1500 radio reset, hold down the up and down buttons for 5 seconds and select radio reset. You will come into difficulties with the sound. This might be from the stereo’s speakers or a phone that is connected to the vehicle.

How do you reset the radio on a 2011 Dodge Ram?

To reset the radio in Your 2011 Dodge Ram 1500, locate the up and down temperature controls and depress them both at the same time until a reset is initiated. Alternatively, try the tune and power knobs, depressing and holding them down for 5 seconds in the same way.

Why does it say UConnect phone not available?

If you get the UConnect phone not available message when pressing the button that means the van is not equipped with the system. It has the button to control it but the other components aren’t there. To get UConnect working on your van you’ll need to have a Mopar accessory UConnect kit installed.