What does it mean if your chainsaw smokes?
When you see a noticeable amount of smoke emanating from the exhaust while the chain saw is idling, it’s time to adjust the machine’s engine idle speed. Exhaust smoke indicates that the machine is idling at too rapid a speed. If necessary, adjust the idle-speed adjusting screw as well.
Why is my chainsaw blowing white?
While black smoke is caused by the burning of more fuel than air, blue or white smoke is generally caused by the burning of excess oil. Often times this color of smoke is caused by a blown head gasket, a worn cylinder or worn rings, or an inoperative crankcase breather, all of which will need help from a professional.
What happens if you overheat a chainsaw?
If you use it too much while it’s overheating, it’s possible you may burn out the engine or pistons causing you to have a broken chainsaw that will either need to be repaired or replaced. Following these tips can help to keep your chainsaw running smoothly for years to come.
Can you overheat a chainsaw chain?
It is normal for the blade of your chainsaw to produce some heat. But it should not overheat or smoke. If you notice any overheating or smoke coming out of the blade, you should stop its use at once. A brief answer is good only for those who are short of time.
What causes a chainsaw to get hot?
Chainsaw engines run at high temperatures, usually in the summer, so they can quickly overheat. If dust, wood chips or other material blocks these systems, the engine will start to overheat. The engine also needs to expel hot air, so the muffler must also be kept clean to keep the engine from overheating.
Why is my chainsaw burning the wood?
If the oil pump for the bar oil is not pumping oil on to the bar it will cause the chain and the bar to get very hot. If this is happening, it may cause the wood to burn.
How long can you run a chainsaw?
Depending on the type and usage, you can expect a gas Chainsaw to run between 15 and 40 min before you have to fill it up again. Most battery-powered chainsaws have a run time of up to 2 hours, but there are high-capacity power packs that will last much longer.
Why does my chainsaw blade get dull so fast?
Your chainsaw blade gets dull so fast because your chain is hitting the ground, the tree is filled with dirt, and/or the bar is bent. These all contribute to the chain getting dull quickly. If you’re cutting through dirty wood, the chain will dull quicker than cutting clean wood.
Should you let a chainsaw warm up?
The gas engine in a gas chainsaw should warm up, but due to the engine’s small size, this will happen quickly. Normally the engine will run for a short time after startup before you really start using it, giving the oil enough time to warm up and lubricate all engine parts.
How long should you let a chainsaw warm up?
About 30 seconds with a few revs.
Can you run a chainsaw without an air filter?
Don’t Run Your Chain Saw With a Dirty Air Filter But if you don’t clean/replace your air filter (shown here), the engine will suck some of that dirt and dust into the combustion chamber, causing excessive wear. Some filters can be cleaned, but others must be replaced.
When should you use a chainsaw brake?
Use the chain brake to stop the chainsaw chain from rotating around the bar when a kick back happens.
How long does it take for a chainsaw to Unflood?
The first is the easiest and most common method. Let your chainsaw sit for 15-20 minutes to allow the fuel to evaporate from the engine and then repeat the starting instructions. This method will work best with a mildly flooded engine.
Do you start a chainsaw with the brake on?
Always start your chainsaw with the chain brake engaged so the chain does not move.
Why does my chainsaw pull so hard?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
Why is my chainsaw hard to pull and kicks back?
Kickback can happen if the flywheel key has gone or the flywheel has moved. This will cause kickback more than once or twice bit every time you try to start it. Check the plug. I would at a guess say clogged exhaust.