How do I reset my Whirlpool Quiet Partner II?

How do I reset my Whirlpool Quiet Partner II?

Try unplugging it for 5 minutes to allow it to reset. The idiot lights just don’t tell us much. The only thing you may not have checked is an obstructed drain hose. Press and hold the heated dry button for 5 seconds.

Does my Whirlpool dishwasher have a reset button?

The Whirlpool machines do not have reset buttons. If you cannot identify the error code, but your dishwasher does not work as expected, perform a general reset. Unplug the dishwasher for a few minutes from the electrical outlet. Wait some time.

How do I get my Whirlpool dishwasher into diagnostic mode?

Here’s the instructions to get into the diagnostics mode: Entry sequence: Press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than 1 second between key presses. NOTE: Some models have replaced the “Clean” LED with “Completed.” The Service Diagnostics Cycle will start when the door is closed.

How do you run a diagnostic on a Whirlpool Gold Series dishwasher?

How do I turn off the control lock on my dishwasher?

To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds. If the dishwasher has a dedicated Control Lock button in the Options selections, press and hold CONTROL LOCK for 3 seconds.

How do I reset my whirlpool?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.

How do I reset my Whirlpool top load washer?

How do you reset a Whirlpool washing machine? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.

What is E1 error in Whirlpool washing machine?

If your washing machine is not working correctly it’s safe to say it’s developed a fault. A flashing FP or F9 E1 error code on the LCD display can ring alarm bells, but it’s typically associated with a water draining problem inside the drum.

Why is my Whirlpool washing machine not turning on?

First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.

How do you fix a washer that won’t start?

Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.

Why does my Whirlpool washer not fill with water?

Washing Machine Won’t Fill Because Water Inlet Valve Defective. Washing machines have a water inlet valve that allows both hot and cold water into the unit. No continuity indicates an issue with the valve. When the water inlet valve is the cause for a Whirlpool Cabrio washer not filling with water, it must be replaced.

What causes a washing machine not to drain and spin?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

How do I reset my front load washer?

How to reset the washing machine:

1. Press POWER to turn the washer off.
2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
4. Plug the washer back in, or turn the circuit breaker back on.

Why is my washer not spinning my clothes dry?

When your washer will not spin dry your clothes, the debris filter or coin trap may be blocked. Your washer has a filtering device down and near the pump called a drain filter or a coin trap. This filter grabs all foreign objects that go down and into the drain.

Why are my clothes too wet after the spin cycle?

The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. Often with this issue, whatever is causing it to not drain during the spin cycle means the water isn’t draining off fast enough and is essentially flowing back into the washer drum, re-soaking your clothing.

How do you fix a Whirlpool washer that won’t spin?

If your Whirlpool Washer is not spinning the problem is almost always the lid switch. If the lid switch is bad you will not hear the motor running when in spin. To check the lid, first unplug the washer.

What would cause a front load washer not to spin?

Front-load washer tubs spin thanks to a drive belt that runs off of the motor. A loose, frayed, or torn belt could be why your washer won’t spin. Overloading your washing machine can cause the belt to loosen or become worn out.

Why is my front load washer not draining or spinning?

Clogged Drain Hose Over time, debris can clog the drain hose and prevent your washer from draining. A twisted or coiled drain hose can also inhibit the free flow of water. Check behind the washer and straighten a kinked hose. If this does not solve the problem, unplug and clean the hose to eliminate any residue.

Why is my Whirlpool washer not draining or spinning?

The Drain Pump May be Clogged or Defective If the hose and filter are both okay, you’ll need to check the drain pump. It may be clogged with debris or could be defective and needs to be replaced. To check this you will need to disconnect the drain hose, and remove the back panel from your Whirlpool washer.