Why does my jeep keep saying perform service?

Why does my jeep keep saying perform service?

All this is is a feature that tells you when to change your oil, instead of relying on the trip odometer or service stickers. Changing the oil will not reset it. you have to do that manually every time you change the oil.

What does perform service mean on a 2000 Jeep Grand Cherokee?

KEN. The Electronic Vehicle Information Center (EVIC) displays a perform service message when distance to service interval has been reached, indicating that regular service and maintenance is due. After performing necessary services, reset service distance by selecting a distance to service interval. .

What does perform service mean on a 2005 Jeep Grand Cherokee?

The perform service message tells you when you need to change oil. To reset it turn the key on and press the step button until miles to service is displayed (it should say 0 underneath). Then press and hold the reset button until it changes from 0 to 3,000 miles.

What does check gages mean on a jeep commander?

The “Check Gauges” light means just that. Look at all the gauges while engine is running and see which one is not in it’s normal range. Gas gauge doesn’t matter. Temperature gauge should be about 195 degrees, voltage should be about 14 volts, and oil pressure at idle is about 40 psi.

How do you reset the oil change light on a Jeep Commander?

Jeep Commander: How to Reset Oil Light

1. Turn the ignition switch to the ON position without starting the engine.
2. SLOWLY press the GAS PEDAL all the way down to the floor THREE times within TEN seconds.
3. Switch the ignition to OFF, then immediately back ON.

How do you clear the codes on a Jeep Wrangler?

How to Clear Codes on Jeep Wrangler

1. Make sure the engine is not running and key is out of the ignition.
2. Disconnect the battery terminals.
3. Wait 5 minutes.
4. Reconnect battery terminals.
5. Insert and turn the ignition key to the run position without starting.
6. All error codes are cleared and CHECK ENGINE icon disappeared.

How do you reset the oil change light on a 2010 Jeep Commander?

2006-2010 Jeep Commander Oil Change Required Minder Light Reset

1. Stop the vehicle and turn the ignition switch to the RUN position without starting the engine.
2. Fully depress the GAS PEDAL slowly three times within 10 seconds.
3. Turn the ignition off and start the engine to verify the indicator has been reset.

How do you reset a 2010 Jeep Commander?

2008-2010

1. Turn the key to ON/RUN position with engine off.
2. Fully depress and release the accelerator pedal 3 times within 10 seconds.
3. Turn the key to the OFF position and then back on to confirm reset was accepted.

How do you reset the oil light on a 2010 Jeep Commander?

1-Turn the ignition to RUN (second position) 2-Press the accelerator pedal all the way down slowly three times within 10 seconds. 3-Turn ignition OFF then turn the ignition to RUN again to verify the maintenance has been reset.

How do you reset the perform service light on a 2006 Jeep Commander?

when it says “perform service”, you press and hold the reset button until it resets. In the menu options, set it for the interval you want to be reminded to get an oil change.

How do you reset the check engine light on a 2008 Jeep Commander?

How to Reset the Engine Light in a Jeep Commander

1. Open the driver’s side door of the Jeep Commander and then locate the Diagnostic Link Connector (DLC) below the dash.
2. Plug the OBD II code reader into the DLC and then turn the ignition key to the key-on/engine-off position.

How do you reset the oil change light?

Hold the Reset Button and Turn the Key Turn the ignition back to the ON position while holding the reset button. Watch the oil change or maintenance light carefully. It should start to blink. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.